Having problems with your Hoover F7412900 Upright Vacuum ?

Replace turbine or control switch for Hoover F7412-900?

\015 I have owned this steam vac for only two years, clean and take very good care of it. But suddenly the brushes won't spin when the machine is turned on. I can turn the brushes manually, filter and brushes are clean. The plastic gear the brushes snap into is not striped, and is in good condition. The only other thing I can think of that will fix the problem with the non rotating brushes is to replace the gear assembly/turbine or the plastic switch that changes the settings. How can I determine if the turbine needs to be replaced, and on a scale of 1-10 how hard is it to replace?\015

Answers :

Repair Help & Product Troubleshooting for Hoover F7412900 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace turbine or control switch for Hoover F7412-900?

... Hoover F7412900 Upright Vacuum

Hoover steamvac turbine and brush control switch

Try checking your drive belt might have come of or just loose ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2

Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.

No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

What's your problem?I have to replace the power switch on my Hoover U6485-900. What part do I need to orer? Wher can I order it?

... Hoover U6485900 Bagged Upright Vacuum

How to replace switch on a Hoover WindTunnel twin chamber bagless vacuum

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh

Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

Replace on/off switch on hoover vacuum

My wife picked one up on the side of the road that someone had tossed. The power switch would not turn off. I took the two bolts out of the top part of the handle, and then removed the screws along the back. This will remove the required panels to ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I replace the on-off electrical switch on a HOOVER Windtunnel Mach 2.1?

... Hoover Vacuums

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?

Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Hoover turbine replacement

First you must remove the dirty water tank then the nozzle window on top of the machine. (this is the clear piece that the dirty water is sucked through.) then remove all 8 screws from the bottom along with the 1 screw on the main housing. after all ... Hoover F7431-900 SteamVac Vacuum

Hoover windtunnel vaccum U6445-900 motor not turning on. I removed the screws and located the contacts inside. There is an on-off switch which seems to be stuck Is there a way to replace this switch

There are a number of Hoover vacuums that are subject to a recall due to an overheating on/off switch. Check out this web site to see if your is included. You'll need the model number and serial number from the back of the unit. The manufacturer w ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace a Hoover Control Cable U6425 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace the switch hoover UH70015 - Hoover UH70015 Bagless Upright Cyclonic Vacuum

... Hoover UH70015 Bagless Upright Cyclonic Vacuum

My wall ceiling fan's control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M

First, you didn't say you checked that the bulb worked. Is that burned out?\015\012\015\012If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same i ... Vacuums

How to replace turbine on hoover steamvac - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

My Sebo hoover trips the house mains sockets every time I switch it on, yet doesn't trip the kitchen mains. Have replaced filters/bag to reduce load but still no good. What should I be investigating in the hoover? Thanks

Hello,It sounds like your vacuum is fine if it works when plugged in the kitchen outlet. It is tripping the breaker switch in the other room because the circuit is overloaded (too many things plugged in this circuit). Try unplugging some things ... Sebo Air Belt C2.1 Bagged Canister Vacuum

Hoover u6425 switch replacement - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Self-propel switch arm broke off where control cable was attached. Looking for instructions as to how to gain access to that switch arm to replace it.

Greetings from GoVacuum,\015\012\015\012This is a farily common repair on this model. What ends up happening is that when someone picks up the vacuum cleaner by the handle of the machine, which on this model also is the controller for th ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

The switch on the wall only works to control the fan and not the light- it won't turn off the ligght. I replaced the switch but it did not solve the problem

If this is a new installation and there was only one switch on the wall, say to control a light that was once there, then you have that switch hooked up only to the fan.\015\012If you want to control the light as well, it has to be wired up at the bo ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4892 seconds