Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

I HAVE A HOOVER POWERMAX CYCLONIC FILTRATION CLEANING VAC 12AMPS AND I CANT FIGURE OUT HOW TO REPLACE THE BELT AND I LOST THE INSTRUCTION BOOK PLZ HELP


Answers :

Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A HOOVER POWERMAX CYCLONIC FILTRATION CLEANING VAC 12AMPS AND I CANT FIGURE OUT HOW TO REPLACE THE BELT AND I LOST THE INSTRUCTION BOOK PLZ HELP


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I am trying to replace the brushbelt. I have the brush off not surewhich end goes where. also I had it on once but the belt was off when it was supposed to on. I cant find my instructions ! help


I am going Kirby "G" crazy.\015\012I hope this URL will be of help to you:\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039\015\012\015\012If it is of help, please rat ... Kirby Ultimate G Bagged Upright Vacuum

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

Need instructions on how to replace the belt on a hoover dirt finder model u5321-930


You can download the manual from the link below:\015\012\015\012http://www.hoover.com/Media/ModelPDF/U5468900.pdf\015\012\015\012Please update the question & let us know if the information given was useful to you - Good Luck! ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I'm trying to replace the belt that drives the sprayer on my Bissell ProHeat but the package with the belts did not come with instructions. I keep finding instructions on the internet, but without pictures, I have no idea what I'm supposed to do. Please help.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Replacing Belt Can't find the manual and it's time to replace the belt. Can someone help with instructions. Thanks!


On the front of the power head is a knob with the KIRBY name on it. Rotate this knob in a counter clockwise direction and it will "lift" the belt off the motor spindle. Release the head lever, only one direction it will turn and remove the head. Tur ... Kirby Ultimate G Bagged Upright Vacuum

Changing belts I cant figure out how to replace belt on my hoover cleaner model u4537-910


Turn vac over, remove the 4 screws holding the bottom plate covering the brush roll. There are 2 belts, one is a V belt ( 38528034) for the brush roll, the other is a flat belt (38528035) that goes from the larger pulley and the motor shat, put it o ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.


... Hoover Vacuums

Belt I can not find instructions on how to replace a belt on the Bissell powwerforce bagless vacuumplease help.


Hi. This isn't a hard repair at all.... Unplug your vacuum. Turn the vacuum beater bar side up. Locate the catches or screws that hold the plate on that covers the beater bar. Remove the plate. The beater bar sits in sockets where it attaches t ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?


Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt replacement cant figure out how to put new belt on...old one broke....


Hello : \015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of the vacuum por ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Lost instruction book


Remove screw on side of unit, slide cover and replace belt with spare on the bottom. ... Oreck XL21 Bagged Upright Vacuum

I CAN'T FIGURE OUT HOW TO REPLACE THE BELT ON MY FOLD AWAY!!!! PLEASE HELP


The manual for this vacuum can be found at:\015\012http://www.manualnguide.com/dl/13985/\015\012\015\012Refer to page 9 for instructions and visuals on ho ... Hoover U5172900 Fold Away Widepath Bagless Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I LOST MY INSTRUCTIONS DISK TO MY KIRBY G SERIES AND I DONT KNOW HOW TO DO ANYTHING WITH IT. I JUST REPLACED MY BELT BUT IT DOESN'T SEEM TO BE WORKING AS WELL AS IT SHOULD.


We have a video, online and printed manuals HERE. ... Kirby Generation 3 Bagged Upright Vacuum

Can't figure out how to replace the belt on a model 116 can you help?Kenmore upright


It should b on the bottom.small screws and plastic groovesto hold it tight,if you like having nails,i would take it to a vac shop. Lots of little shops in the yellow pages ... Vacuums

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

I replaced the belt on the vaccum cleaner for the brush and it just seems too loose. How do I tighten it? Do you have a diagram I can look at. I lost my instruction booklet.


Are you certain the belt is on the idler arm and that the spring is still in place? The belt has to sit on the small wheel to provide tension on the belt. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to replace belt #38528-033 on a Hoover WindTunnel vacuum model #U5463-960. I've had the vacuum for a long time and have misplaced all operational and instructional info that came with it. Any help would be appreciated. Thank you.


Replace the belt on a hoover washing machine ... Vacuums

I lost my instruction book for the Bissell Steam Mop model 1867-7. Help


Go on line there all over the place and download it. ... Bissell 1867 steamMOP Stick Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0937 seconds