Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?
The machine will not start up
\015 The machine makes a low humming sound instead of starting up\015
The motor is seized up. You will have to replace the motor. If can order it online for about $75.00. If you can not do the work yourself take to a vac repair shop they will most likely charge you $40.00 to do the work. Good luck.
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e
The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.
I have a dirt devil bagless cannister,machine will start and vacuum nicely then shut itself off probably beczause it is over heating and will not start again for at least an hour. Does this machine have a heat sensor and is is fixable?
The vac very likely has a thermostat located near the suction motor that will stop the motor to keep it from burning itself out. These thermostats rarely go bad. You need to look for a blockage starting with the power nozzel (carpet sweeper) all the ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
Lately we've been having plumbing problems to where our washing machine floods up our bath tub and toilet. And it happens while we have the washing machine on of course. Another problem is that whenever we are taking a shower our tub starts to clog up and water starts pouring out from the bottom of our toilet. We had a plumber come by to root out our pipes just last week and it was fine for about 3 days. And now the problem is back and driving me crazy. WHAT IS WRONG AND HOW CAN I FIX IT??
Possible tree roots best thing is to hire a plumber with a camera snake ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum
I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the
If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums
My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil
My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.
If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums
I have a kitchenaid artisan coffee machine which is 15 months old just out of warranty. when you start to make an esspresso coffee the machine runs but no water is being pumped through the coffee to the cup you can hear the machine working but no coffee. Thanks Lloyd
Hello lloyd..... There are a few possible causes of this problem. The first is using coffee which is too fine a grind. The second is a machine which needs to be thoroughly cleaned. Most can fix those two areas themselves. The other causes have to ... Vacuums
Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance
Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum
When the water tank is filled it leaks before the machine is started what is the problem the machine has only been used a couple of times
Excwss detergent and or too much water. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have konica 7145 machine. i am start a machine but error F-51-4, please my solved problem
Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn
Model 2100 canister: Red light comes on to indicate bag is full and machine shuts off. The bag is empty...when I readjust bag, machine will start up again but shut down shortly.
Try this \015\012Electrolux LE, 2100 Hi Tech Canister ... Vacuums
I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?
... Continental Vacuums
We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started
There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!
Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but
Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
The machine backs out of the dock, then proceeds to turn in circles, stop and then start turning in circles again. I have cleaned all of the sensor areas and made sure the bumpers were not stuck against the machine. Any ideas
... iRobot Roomba 560 Robotic Vacuum
After entering time on the touch-pad and touching 'start' ; the machine starts but I can hear the power going up and down, the light blinks partially. The bell does not ring at the end of the 'time' and the food is only partially cooked./Bob
Although, this is listed under vacuums \015\012\015\012"After entering time on the Problem with the Vacuums" (sic)\015\012\015\012"The bell does not ring at the end of the \\'time\\' and the food is only p ... Vacuums
Hi monarch 650 duct cleaner when we connect the hose to the point the machine start and when we take off still the machine working what is the problem Tommy
The clean water is leaking straight out through the bottom of the machine. This just started out of the blue. I cannot use the machine because of this. Any ideas?
It sounds as if the reservoir is stuck open. If you look behind the upper tank, you will see a rod that opens the reservoir when the handle release is squeezed. This part may need replacement. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
I have a Bissell 3576-2 sweeper. It's worked for years, but now it won't start. The light turns on but the motor doesn't. Before this problem started, I took the machine apart to clean all
... Bissell CleanView II Plus Upright Bagless VacuumVacuum
The machine will not start up
The motor is seized up. You will have to replace the motor. If can order it online for about $75.00. If you can not do the work yourself take to a vac repair shop they will most likely charge you $40.00 to do the work. Good luck. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum