Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

Hoover steam vac model f7425-900 filter is

\015 This is a 6 brush model, the brushes do not rotate, the filter is clean and the switch is in the on position\015

Answers :

The brush system on this model has a poor engineering design in that the brushes are running off an air turbine, which uses a steel bushing to spin the turbine which gets rusty from the moisture when the machine is being used. No long term solver. I would replace the machine with a Dirt Devil Platinum Force model
If you are not looking to buy a new $200 machine you can replace the Turbine Gear for $32. Follow the link below.

Hoover SteamVac Replacement Turbine Brush\015\012 Gear Part # 91001097 replaces part numbers 43191006 and 43191018

Hoover F74XX Parts Link

http://www.usavacuum.com/Hoover-Steamvac-s/109.htm

Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover steam vac model f7425-900 filter is


The brush system on this model has a poor engineering design in that the brushes are running off an air turbine, which uses a steel bushing to spin the turbine which gets rusty from the moisture when the machine is being used. No long term solver. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and


The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Dual V steam vac model F7425-900 won't dispense detergent


Check the spring loaded valve at the bottom of the detergent bottle.\015\012Push it up with your finger or a pencil or some such thing and see\015\012if fluid comes out. If it does, then the problem is the valve or tubing I\015\012w ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover Steam VAc carpet Model F7425-900


Take out the brush block, make sure that the shaft is ok, it goes up into the turbine, which is what drives the brushes. If the shaft is ok, then the turbine either needs to be cleaned and lubed, or replaced. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I need a diagram to install a turbine in a hoover steam vac model f7425-900


If you give me your name, address, city, state and zip code\015\012I can send it to you in the mail. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Hoover Steam Vac Model F7441-980. The


... Hoover V1 SteamVac SpinScrub Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Hoover steam vac model f5857-900 manual - Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM


... Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move


There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie


The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Steam Vac model: F7425-900


I had the same problem 2 weeks ago.I took apart the turbine and found that there are two bearings that hold the main gear that were rusted fast. I put some 3in1 oil on them and kept on trying to break them free by turning them,it worked great. Just k ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac model 7210-900


Did you clean both filters? There is one on the tank and the other is from the bottom, it ha a red frame, pull it out to clean. Pull the brush block out, is the shaft that goes up into the machine broken off? If so replace the brush block. While ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Lost Manual for Hoover Steam Vac Model #5906-900


Visit www.hoover.co.ukThere you can pick after sales service,instruction manuals, etc. etc.You will find your manual there.I hope this helps ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]


The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac Model F5876-900


... Hoover F5835900 Upright Steam Vacuum

The trigger doesn't work on my hoover steam vac, model F5865-900


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

We seem to have lost our manual to our Hoover Steam Vac V Dual with rinse, Model F 7220 - 900 and were told by Hoover Rep. that we could download it from this website. How do we do that? I don't see an option for downloading manuals. Thank You, Kathy Crawford


... Hoover Vacuums

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!


... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

How does the upholstery cleaning hose attach to the vac? Hoover Steam Vac Deluxe Model # F5860-900 Series 17.9


See if this manual helps:\015\012http://www.hoover.com/pdfs/manuals/F5857955.pdf ... Hoover Steamvac F5860-900 Vacuum

Hoover model 5910-900 - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover steam vac model # f7441-980 - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618767&thid=459387\015\012Hoover steam vac\015\012Posted by beverlyarm on Mar 21, 2008\015\012Hoover steam v ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover steam vac ultra model F5883-900 - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover steam vac dual model F7425900


If you are talking about the brush block, take it out and see if the shaft that goes up into the turbine is broken off, if not, then the turbine has gone bad and will have to be replaced. The turbine is what turns the brushes. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0888 seconds