Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

BRUHES WON'T ROTATE

\015 BRUSHES WON'T ROTATE\015

Answers :

The brushes are operated by suction from the motor. Most of the problems with these models are in the turbine, it just needs to be serviced, some replaced. You can check the filter under the bottom (a red or white pull tab). Also check the lid on the lower tank to on properly.
The bearings in the turbine that turns the brushes are very cheap. They rust and seize. Sometimes they can be greased and reused. If the corrosion is too bad the turbine has to be replaced.
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hoover all terrain cleaning for carpets and hard floors and the Brushes will not rotate. I have replaced the filter on the bottom which is recommended by hoover and the brushes still wont rotate. Please advise


I assume this unit has no mechanism to turn the brush but instead using the air flow to activate the brush, in this instance it could be that there is dirt which is caught up in the brush which is stopping the rotation.A nice good clean and make sure ... Hoover Vacuums

Cleaning brushes wont rotate


I understand how important the brushes are when cleaning. You may want to the check the pump belt for breakage for the brush belt and pump belt work in conjunction with the pump. If you're still experiencing difficulty, you may want t ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The beater bar wont rotate when set to floor cleaning on bissell aromatic carpet shampooer


... Bissell Vacuums

Brushes wont rotate


The belt has streached go to walmart and get a new one. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

BRUHES WON'T ROTATE


The brushes are operated by suction from the motor. Most of the problems with these models are in the turbine, it just needs to be serviced, some replaced. You can check the filter under the bottom (a red or white pull tab). Also check the lid on the ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Dyson dc 35 the floor brush wont rotate


My brush on my Dyson DC35 wont spin. ... Dyson DC35 Handheld Vacuum

Brushes wont rotate


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The brushroll wont spin on my shark rotator the light isnt red but green light is dim


Call cust. service. They should replace the head. ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Air powered turbo brush on shark navigator wont rotate


... Euro-Pro EuroPro Shark Navigator Vacuum

MC-V9635 Hey i have a panasonice mc-v9635. The roller isnt working because the belt is locked so that it wont rotate.


... Panasonic MC-V9635 Canister Vacuum

Every thing clean & sucking well except wont pickup off floor. brush in good condition &rotating. any answers would help.


This is hard to answer without see it in person. Check and make sure there is no broken pieces on the bottom where you could loose suction. Also make sure you have the machine set correctly for either bare floors or carpet. If it is on set on carpet ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Roller brush wont rotate my bissell series 3760-5


... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The scrub brushes wont rotate - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


Clean it should be hair struck ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia


I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brush wont rotate - Vacuums


Without known the type or model of the vacuum you can only check a few generic design futures. \015\012There is only one motor which turns the turbine and brush. Therefore, if the suction from the turbine works check the belt by r ... Vacuums

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?


Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?


Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

The brushes on my new healthy home vacuum wont rotate when the machine is turned on how do i access the belt location


If you turn the vacuum over so you can see the brush roll, there is a brush cover that is held on by (4) screws. Remove those screws and the base plate cover will come off. With the base plate cover off you can access the roller brush an belt. If you ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The rotating brush on my Dyson DC25 wont go round - can you help - the machine is new but I don't have the manual?


... Dyson DC25 All Floors Bagless Upright Vacuum

I have a bissell proheat turbo2x the brushes wont rotate checked for blockages none to be found can anyone help


The belts are probably broken, stretched or worn. I would try replacing the belts if you haven't in a while. You can get the belts you need here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Turbine headbrush wont rotate - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Make sure it's pluged in to exstention pole secure and switched on ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

The brushs doesnt rotate


There are two belts on the 1698 one for brushes one for pump check the link belowhttp://www.vacsite.com/en/bissell-parts-1/bissell-par ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Turbo brush attachment won't rotate


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0216 seconds