Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

After cleaning my steam cleaner, the brushes won't spin. They snap in but when turned on won't spin.

Answers :

Hi There,
\015\012Here's how you may diagnosis your Hoover SteamVac brushes when they don't spin. It's either the brushes are dirty and need to be cleaned, the brush block itself has gone bad and needs to be replaced, or the internal turbine that spins the brush has gone bad and needs to be replaced.
\015\012Here's a step by step instruction on how you can diagnosis the brushes not spinning:
\015\012If you need to replace the turbine, here's a link to a repair that I did on how to replace the turbine assembly:
\015\012I hope this helped you. Please leave feedback, or rate my repair helpful if this answered your question. If you need further help on this repair, please just use the comment field on the repair page and I'll be more then happy to walk you through some more advanced diagnosing that you can do.
\015\012Thanks so much,
\015\012Chris Jones
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After cleaning my steam cleaner, the brushes won't spin. They snap in but when turned on won't spin.

Hi There,\015\012\015\012Here's how you may diagnosis your Hoover SteamVac brushes when they don't spin. It's either the brushes are dirty and need to be cleaned, the brush block itself has gone bad and needs to be replaced, or the inter ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover steam cleaner spin scrub brushes wont turn cant find belt

I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt probably broken. unplug from power and remove the plate from the bottom of cleaner.belt should be visible on one side or other. ... Hoover F5891-900 Steam Cleaner


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a steam cleaner and i can not get the black arm brush to keep one side up and when you trun on the steam cleaner the brush dose not spin when you start to clean the floor but it will spin when you have it siting up right

Sounds like you could have an elevator broken (part #2000010). You will have to take the top off to replace them or to check to see if one of them is broke. There is one on each side so when the handle is in the upright, they push againsy the brush ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover terrain steam cleaner, brushes wont spin

The primary problem is that the turbine is seized. One way to verify this is to try to manually move the brushes by hand (with it off, unplugged). If not then your problem is with the turbine. This usually requires professional service. I would recom ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine

... Bissell 8910 ProHeat Clear View Upright Vacuum

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate

If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 

For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

My hoover spin brush steam vac brushes wont spin

Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Brush will not spin on the steam cleaner - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My brushes wont turn on my f7412900 hoover steam vac dual v

... Hoover Vacuums

The brush won't spin on my Hyla Vacuum Cleaner. The vacuum does turn on. Am I missing a small connection?

... Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.

You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin

The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Brushes can some one please help me with my steam cleaner I have never used it myself but someone else did and Im not sure how to turn the brushs on .....i have never used it

Sounds like the belt is broken or at least the brushes are bound up with carpet fibers. Take a look and see which it is. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The brushes on my Hoover steam spin carpet cleaner will not spin.

Clean the small TURBINE filter under the clear plastic housing. If that doesn't work remove the brush assembly and see if the drive is turning. If not, you can easily access the turbine(and gear assembly) to examine components. My $5 flea market un ... Hoover F5906-900 Upright Steam Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Hoover steam vac dual v's brushes will not spin and the square that the peg goes into wont spin either. There is suction but it is making a loud noise.

Sometime when the brush is not turning their are less resistance to the motor, so it will turn allot faster than normal. The turbine gear assembly which connected to the brush assembly probably broken, all the g ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes

(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.7402 seconds