Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

Brushes not rotating on hoover f7425-900 steamvac v2

\015 Purchased and installed new brushed as the cog spindle was broken off. However still does not turn brushes. Appears cob spindle is not being turned by female connector in main unit. Rest of steamer works, i.e. water spray and return vacumn. is there a belt and or motor that needs to be looked at, no apparent entry to see.\015

Answers :

I had the same problem and it was inside the turbine assembly. If you take the turbine assembly off the machine and open it up, you will see the turbine blades on one side and the reduction gears on the other side. The problem on mine was a needle bearing sandwiched between two washers on the reduction gear side. This bearing/washer stack is the stabilizer for the turbine gear shaft. Mine was rusted solid. I removed the washers and bearing and cleaned them up with a wire wheel being careful not to lose any of the tiny needles. Once evrything was rust-free, I reset the needles with grease and sandwiched the bearing between the washers. I then reinstalled this stack back in the case along with the other gears, regreased everything, and buttoned it up. Brushes are spinning better than they have in a long time.
The turbine is what turns the brushes, they get gummed up is one problem when they don't work.. Most times they get replaced. You have to take the top noozle off to get to the turbine.
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes not rotating on hoover f7425-900 steamvac v2


I had the same problem and it was inside the turbine assembly. If you take the turbine assembly off the machine and open it up, you will see the turbine blades on one side and the reduction gears on the other side. The problem on mine was a needle ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

On hoover steamvac F7425-900 brushes do not rotate. I have cleaned the filter


May be the motor is the problem ... Hoover Vacuums

How do I change the belt on a Hoover Steamvac Model # F5905-900. The brushes are not rotating strong enough. They rotate while they are off the carpet but once you lower them to the carpet they stop rotating.


... Hoover F5905-900 Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Rotating brushes don't rotate - Hoover F5872-900 SteamVac Wet/Dry Vacuum


Check belt, may be broken or may have come off the brush bar and replace. ... Hoover F5872-900 SteamVac Wet/Dry Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

I have a Hoover Agility Steamvac and the brushes will not rotate. I have cleaned the filters and the the "brushes on" feature has been selected. Any suggestions on what else I might try to get it working?


You have a broken brush bar belt. Just simply replace it with a new one. This is very cheap and easy to fix.Pull the cover off of the bottom of the Vac and the belt will be there. If it's not broken then it is still stretched to the point ... Hoover Vacuums

My Hoover Steamvac- the brushes are not rotating neither L or H


My hoover steamvac the brushes are not turning what makes the blue triangle that the brush attachement fits to move? ... Hoover F5900-900 Upright Steam Vacuum

Brushes do not turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


The brushes are turning by an air driven turbine. The turbine has a \015\012pivot bushing made of steel inside of it that gets rusty because of the \015\012water that is running through it. The turbine will have to be replaced.\015\012 You can fin ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes donot turn when asked to shampoo - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


The brushes are turning by an air driven turbine. The turbine has a \015\012pivot bushing made of steel inside of it that gets rusty because of the \015\012water that is running through it. The turbine will have to be replaced. You can find a genu ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

How Do I Replace/Install the Hoover SteamVac Replacement Turbine Brush Gear Part # 91001019, 43191006, 91001097 - Its for a F7425-900. Is There a manual?


... Hoover V1 SteamVac SpinScrub Vacuum

Brushes don't rotate - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Hey are driven by a belt just replace it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I need the manuel for the hoover steamvac deluxe 5 rotating brushes . the model is F5864-900


Http://www.vacshopusa.com/pdf/hf5837900.pdfHere is the schematics ... Vacuums

Why did the brushes stop rotating? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


It could be a few different reasons, 1. The belt is broken, 2. The motor has died, 3. There is an obstruction, or some such thing stopping the bar from rotating (often hair and/or string) 4. The contact switch is defective. (switch that turns beater ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes don't turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


I had the same problem and found a manual online. I never realized that there was a filter in the bottom of the machine. There are 2 red tabs, squeeze them together and pull ( I had to use a pair of pliers to pull). Note which is top and which is bot ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My spin scrub brushes don't spin at all. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Check that the belt that spins the brushes is not broken, also that the\015\012gear that drives the belt is turning.\015\012\015\012Tom ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes will not rotate on my steam vac - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


I'm sorry to tell you that you have a broken drive brush. One of the brushes has a stem, and that stem is broken. See if you can remove the brush assembly - I believe it pulls straight down. See if one of the stems is a little longer than the othe ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

F5860-900 Hoover Deluxe Steamvac with 5 rotating brushes


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brushes are not rotating - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this problem.First, what you'll need to do is take the brush block out of the machine. To do this there are 4 clips on the brush bloc ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Srub brushes not turning - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


You will find broken belt or something is jamming it ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Why did the brushes stop rotating? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Please check two things: \015\012(1) The shutoff switch on the hood is NOT set to OFF for brush speed.\015\012(2) Remove the red filter panel from under the cleaner, behind the brushes, and clean the hair/debris from the screen filter. S ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I lost the manuel for my hoover steamvac ultra. it has 5 rotate brushes.


Http://www.hoover.com/CustomerService/Manuals/Default.aspx \015\012 \015\012This is the link to the Hoover manuals. Hope t ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover Steamvac Deluxe with 5 rotating brushes


... Hoover F5888-900 SteamVac Upright Wet/Dry Vacuum

Brushes will not rotate - Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum


I can't tell for sure from the pictures, but there are two possibilities - the drive belt to the brushes broke, or the brush can't turn due to excessive hair wrapped around the shaft. If the belt is OK but the brush does not turn, you should smell b ... Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

The brush does not rotate - Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum


... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0724 seconds