Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?
Cleaning brush assembly on steamvac
\015 I've lost the manual for my F7425-900 steam vac and am trying to clean it before I put it up. I've gotten the brush unit off of the bottom of the steam vac, and there is a lot of lint and dirt in between the brushes and crammed up into the brush unit. Does this unit come apart? It looks like it should, but I can't figure it out.\015
Yes this does come apart. The clear plastic pieces clip into the black plastic piece, flat tip screw driver inserted into the gap can release the clips and allow for cleaning.
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Cleaning brush assembly on steamvac
Yes this does come apart. The clear plastic pieces clip into the black plastic piece, flat tip screw driver inserted into the gap can release the clips and allow for cleaning. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch
... Hoover Vacuums
My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab
(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum
Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and
The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.
... Electrolux Vacuums
Is it possible to take the Hoover Brush Block Assembly F7220-900 #48437029 apart so that I can thoroughly clean inside the block? It looks like it could, but I don't want to break it by trying.
... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t
Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther
... Clarke Vacuums
I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?
Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
The brushed on my steamvac Dual V F7227 are no longer working. We have pulled and cleaned the brushes, and the filter, but the brushes still will not come on. I saw a reply to one person that it is the belt. If so... how do I change it?
Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
How to clean my Hoover steamvac brushes? or
Http://www.hoover.com/pdfs/manuals/F5914900.pdf Press all four latches (B) and pull brushblock out. The brushes can be cleanedunder running waterGodbless ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
My husband took the brush and base assembly apart to clean the unit...when he took the wheel assembly off the small white leveller inside fell off. How do we get this back on??
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??
Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?
If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.
I have a Hoover Agility Steamvac and the brushes will not rotate. I have cleaned the filters and the the "brushes on" feature has been selected. Any suggestions on what else I might try to get it working?
You have a broken brush bar belt. Just simply replace it with a new one. This is very cheap and easy to fix.Pull the cover off of the bottom of the Vac and the belt will be there. If it's not broken then it is still stretched to the point ... Hoover Vacuums
Hoover SteamVAc LS - brushes turn slowly
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Bissell little green clean machine brush assembly
... Bissell 1725-1 Little Green ProHeat Wet/Dry Vacuum
How do I remove brush bar to clean the housing assembly on a Dyson DC28?
Area of trapezoid ... Dyson DC28 Animal Bagless Upright Vacuum
Have a Hoover Steamvac F7410-900, the brushes don't spin anymore. Can hear the motor running. There is no visible debris and the lint screen is clean. Please HELP! I miss my steam cleaner. Thanx!
Check to see if you can turn the brushes by hand, if not your bearings need service in your turbine assembly.Check aslo for proper suction at the instake standpipe under the lower tank. If it is the turbine, take it to a repair shop. ... Vacuums
Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL
... Bissell 1200A SpotBot Pet Robotic Vacuum
Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?
... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner
How do you remove the brushes on a hoover steamvac to clean them?
Hoover makes running changes on these style steamvacs without changing the model numbers. One of the following or both. \015\012 \015\012Four tabs (opaque/white in color) about a 1/4 of the way in from each corner of the plastic ... Hoover F5870-900 SteamVac Vacuum
On hoover steamvac F7425-900 brushes do not rotate. I have cleaned the filter
May be the motor is the problem ... Hoover Vacuums
Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.
Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover towar ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum