Having problems with your Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum ?

Missing valve for the detergent

\015 The valve at the bottom of the detergent tank is missing. I'd like to buy one but no one seems to offer parts at this level of detail.\015

Answers :

Go to www.TheHooverStore.com. I'm researching the potential repair of my tank as well and stumbled across this website. They offer just the valve for $5.99. Good luck!
Repair Help & Product Troubleshooting for Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Missing valve for the detergent


Go to www.TheHooverStore.com. I'm researching the potential repair of my tank as well and stumbled across this website. They offer just the valve for $5.99. Good luck! ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Spring loaded valve under the detergent mix system is broken or missing some part that holds it in


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My Hoover 97441-980 Dual Steam Vac won't hold detergent. The valve is bad. How can I get the old valve out so that I can replace it?


Just grab the valve stem with a pair of needle nose pliers and pull it out, then you can gently work out the outer valve with the pliers, and then remove the gasket. The older tanks tend to crack around the valve which may be the whole problem, but t ... Hoover Vacuums

Hose valve linkage is missing, how do i replace it


Http://www.onlinevacuumparts.com/ps-105-9-hoover-self-propelled-bagless ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Delonghi ECO310 BK espresso coffee maker. The unit is leaking from the steam solenoid valve on top of the boiler unit. The Teflon pipe that's retained by the clip is not a tight fit and is able to slide in/out slightly. There is a red gasket present, that sits over the tube, but I suspect that there may be someting else missing from the assembly because of the play in the pipe. Does anyone have a an exploded diagram of the assembly or can confirm that it is just the gasket that is likely to h


... Vacuums

Tank Dispensing All the detergent empties out, but water does not. This is brand new. Have checked valves & everything checks out ok.


Nattim;\015\012\015\012What I have done is to forget about the detergent container which doesn't standup to ordinary use and go and buy a small tank sprayer and fill it with the detergent solution\015\012-----------and then spray th ... Hoover F7222-900 SteamVac Upright Vacuum

The clear water tank/ detergent mix, a valve sticks open. What can I do. I have to reset it with a long wooden spoon. Any ideas ??


Empty the water from the tank. Coat the seal around the valve with petroleum jelly. Open and close the valve with your wooden spoon to get it coated really well and try refilling it again with water to see if it solves the problem.If it ... Vacuums

Hoover carpet cleaner F7458-900 issue The detergent is not dispensing? Tried cleaning the valve cap (per Hoover manual) yet the issue persits. Any advise?


The pointed valve that is in the tank may need replacing. The two valves are a set. I just ordered some from www.usavacuum.com ... Hoover F7458-900 Upright Vacuum

Where can I get the valve


Try this site:  http://www.daltonvacuum.com/scripts/ProdList.asp?idCategory=258&nameCate=Hoover&nameSubCate=Steam%20Vac%20Parts ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions: 1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP. 2. Where can I get the valve or the parts? My zip code is 77479 and I ca


Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective :) \015\012\015\012press add a comment in upper right corner if ... Vacuums

Hoover dual V. DETERGENT DISPENSER WILL NOT DISPENSE.


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover Dual V steam vac model F7425-900 won't dispense detergent


Check the spring loaded valve at the bottom of the detergent bottle.\015\012Push it up with your finger or a pencil or some such thing and see\015\012if fluid comes out. If it does, then the problem is the valve or tubing I\015\012w ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Detergent won't dispense


Check the valve at the bottom of the tank, does it push up then come back by itself (part #43513014)? If it is ok, then there may be a problem with the plate that the tank sits on or the plunger inside the handle isn't pushing to release the deterge ... Hoover F7220900 SteamVac V2 Upright Vacuum

Replacing valve on water tank on hoover steamvac


Buy the whole tank not worth the time to repair the valve ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed


It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

Which tank holds the water and detergent.


The tank with cap will holds the detgerent ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Delonghi DSS50 steam floor cleaner water reservoir has a broken valve on the bottom where it fits into the steam unit. It leaks water rather than producing steam. I would like to find the valve and replace it or buy a new water reservoir with the valve in it. I cannot find the part I need. Can you help me?


... DeLonghi DSS50 Scopa Upright Steam Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper


... Vacuums

Relief valve? can you help have a dyson dc08 great machine but keeps popping and suction's reduced as if a relief valve has opened swich off then ok again until you make it pop again does this more if your using just the hose no attachments cheers pete


Hi,\015\012\015\012I had the same problem with my DC08. What I had found is that cleaning the main washable filter will remove the problem. I have a log fire at my place and I have found that the vacuum does not like the dust from the f ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Belt replacement appears to have 2 belts, 1 is on and 1 is missing, the belt that is driven by the motor is missing, how do I remove the clutch housing where the belt goes?


Hi.\015\012\015\012You are correct there are 2 belts.\015\012They can be tricky to replace most shops will state they cant be replaced & you require new clutch.\015\012So try this site ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi my friend filled the detergent tank on my steam cleaner with straight Laundry detergent now it's only producing suds how do I stop it so it can work properly?


You'll have to rinse it until the detergent is out. Add a little salt to the rinse water. It will help eliminate the sudsing. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I'm trying to use the reverse flow hole on my Miele s712 to blow up an air mattres. None of my fitting appear to fit so I can use the hose. Is there something I'm missing? Is there a trick of the trade? Or am i missing some gear. It's new, out of the box but I just can't get the hose onto the reverse flow. The Poduct is a Miele S712 vacuum dispite what this system has allowed me to enter. ; )


I GO THROU INSTRUCTION BOOKE OF SERIES 700 I DO NOT FOUND THIS REVERSE FLOW......THANKS ... Miele S548 Bagged Canister Vacuum

Missing parts missing o ring around main body and need wheels


I need a new wand solution tube, Part Number 016-9463, for my Bissell Power Steamer Model number 1631. Actually, the nozzle at the end of the tube has broken, and I need to replace it, but I imagine I would have to buy the entire part, hose and nozz ... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

Hoover SteamVac Is there a spring in the trigger. The valve was is two pieces and we glued it together and it still won't retract. Is it possible there was a spring in the trigger that got lost or do I need a new valve? redevil16 helped me last time. Hopefully he or someone can help. Thanks, Sandy


I'm not sure what your referring too, but Here is how it works. The trigger is snapped into two "rocker retainers" in the handle. when you pull on the trigger, it rocks and pushes on a rod that goes down to another shorter rod and that one pushes on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

There is a rubber valve on the top of Dyson DC14 all floors. When the vacum is locked in its upright position or the hand wand is used there is a whistling sound coming out of the valve. When the vac is used as a floor vac, it does not make the sound. Is this something that I can fix? Is there an obstruction somewhere that would be causing this sound? thank you.


The Fixya user in this repair is giving out personal contact information rather then helping the customer out on the Fixya board. This defeats the whole purpose of Fixya if the "TheDysonTeam" just gives out his phone number and helps the customer o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0135 seconds