Having problems with your Hoover F7431-900 SteamVac Vacuum ?

Spin-scrub brushes do not spin

\015 Hoover spin -scrub machine, brushes do not spin\015

Answers :

Hello. there is a little window by the brush control. if you open it up, you can see that there is maybe some lint covering it. scrape that off, and try again. make sure your lever is set to brushes and realease the handle release. if this doesn't work, then you probably have a problem with your gear box. this can only be serviced at a repair shop. I hope this helps. Let me know! Thanks, Renevacdoc
Repair Help & Product Troubleshooting for Hoover F7431-900 SteamVac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.


... Vacuums

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???


... Vacuums

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.


Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover spin scrub machine has stopped scrubbing. It still dispenses and pulls up the water, but the brushes don't move. I've checked the on off button for brush control and cycled it to off and back on, but no movement out of the brushes.


There is a filter on the front right hand side of my F5871-900 Hoover. If you remove the plastic covering and clean that filter (wet finger may do), you're Hoover will begin spinning again! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]


The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spin-scrub brushes do not spin


Hello. there is a little window by the brush control. if you open it up, you can see that there is maybe some lint covering it. scrape that off, and try again. make sure your lever is set to brushes and realease the handle release. if this doesn't ... Hoover F7431-900 SteamVac Vacuum

Why won"t the brushes on my Hoover spin scrub spin?


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

HooverSpin Scrub and the brushes always stop spinning.


Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.


You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Help. The brushes on my Steam Vac Spin Scrub


If you don't have the user's manual for the machine, here it is:www.thinkvacuums.com/pdf/uprights/Hoover_F5914900.pdfCheck your system for any obstructions that could possibly causing the problem. Also, remove the brushes and see if ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spin Scrub Brushes won't turn


If the brushes quit spinning, either the brush block shaft that goes into the turbine broke off, or the turbine is bad. This unit is tricky to take apart and then put back together again. But pull the brush asm off, then start taking out screws. B ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

The scrub brushes dont spin anymore


The brushes are turning by an air driven turbine. The turbine has a \012pivot bushing made of steel inside of it that gets rusty because of the \012water that is running through it. The turbine gear will have to be \012replaced.\012 You can access ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover spin scrub brushes won't spin


... Hoover SteamVac F5912-900 Spin Scrub TurboPower Carpet Cleaner

My spin scrub brushes don't spin at all. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Check that the belt that spins the brushes is not broken, also that the\015\012gear that drives the belt is turning.\015\012\015\012Tom ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Hoover spin scrub carpet cleaner and the brushes won't spin?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover FH50044 spin scrub. Brushes won't turn. All is clean. Brushes turn by hand when on the machine. Any help.


... Vacuums

Hoover Spin Scrub model # F7410-900. The brushes will not spin.


Take the brush block out, is the shaft still on it or did it break off, if it broke off, then replace the brush block. If it is there and you can turn the brushes by hand, then the turbine is bad. Sometimes you can clean it out, most time you have ... Vacuums

Hoover spin scrub brushes won't turn


... Vacuums

Hoover steam cleaner spin scrub brushes wont turn cant find belt


I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How to remove brushes on hoover spin scrub - Hoover Vacuums


... Hoover Vacuums

Brand new hoover steam vac max extract. brushes won't spin. I have check connections, read the manual and nothing. have the switch to power scrub. works with hand tool.


... Hoover Vacuums

The scrub brushes are not spinning, mod.f 5869-900


NEED REPLACED TURBINE ASSEMBLY-SVPart Number :90001355 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0608 seconds