Having problems with your Hoover F7431-900 SteamVac Vacuum ?

Brushes are not spinning we think it is a belt problem

Answers :

It may very well be that a belt is broken that runs the brushes.\015\012However, the question is, what caused it to break?\015\012Most likely your brush needs to be removed and cleaned. Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn freely. If they do not, spray a bit of WD40 between the brush and the holders and rotate the holders around the brush. Doing this will clear up the most common occurring cause of the problem you are facing. \015\012
\015\012Once the brush is cleaned, replace the belt that drives it and reassemble the unit.
Good luck and feel free to contact me if you find this does not solve your problem.
Repair Help & Product Troubleshooting for Hoover F7431-900 SteamVac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Brushes are not spinning we think it is a belt problem

It may very well be that a belt is broken that runs the brushes.\015\012However, the question is, what caused it to break?\015\012Most likely your brush needs to be removed and cleaned. Clean all debris that might be in the bristles of the brus ... Hoover F7431-900 SteamVac Vacuum

Brush not spinning , no belt is needing to be replaced, i think something in switch, cause before this problem the switch was always on , i would plug/unplug to turn it on. thisis case with 2 vacuums i have

... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover U5780 Brush Won't Spin (Have New Belts)

... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

The roller brush underneath is not spinning when the vaccum is on, it does spin freely, I'm thinking maybe there's a belt inside that may have come off?! Is it easy to fix or replace this?!

Power drive windtunnels need to be serviced about once a year. Take it to a vac shop. Your belts need replacing and idler pulley needs adjusting ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a bosch bagless jet 12 amps/1450 W which I got secondhand. the switch to operate the powerhead (the rug brush) no longer gives me any results. I don't have the right tools to unscrew the plates and look for a belt. I don't think it's a belt problem anyway because I don't hear the powerbrush motor turn on, either.

... Bosch Vacuums

Bissell 8910e Aromapro. Jams when being pushed along floor. I think brushes drop down and cause problem. However brushes turn when machine is laid flat. Motor works. Doe it need new belt ?

Check your depth adjustment on your brushes ... Bissell Vacuums

The brush-head on my Dyson doesn't spin, and there is a loud rattling sound comming from the belt assembly. I've inspected the belt assembly and everything "looks ok". What could be the problem, and how can I fix it.

Sounds like the belt is just broken friend. If you have one, just remove the brushroller from the head of the vacuum and replace ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Not enough suction going into my turbo brush so it spins. Ive cleaned it checked the belt it still doesnt spin. how to fix this problem?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My manual says it is DC07, but it is pink and silver in colour. I have 2 problems, firstly the brush has stopped spinning, but belt appears intact. Secondly there are tiny holes in suction pipe near brush i.e. the little section of suction pipe at base of vacuum cleaner.

Hi there, \015\012The DC07 came out in a few different variations so the colour only indicates that yours has a hepa filter. The first problem can be caused by a few different things\015\0121. the brush roller bearings are worn or siexed. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Where is the belt on a hoover agility?? My brushes stopped spinning and I think that the belt broke but I cannot find it

If you have the manual it should show the location of the screws or clips that hold the cover on for the belt. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Brushes are not spinning. think the belt is off or broken. how do i access the belt?

There is no belt in this machine. The brushes are turning by an air driven turbine. The turbine has a pivot bushing made of steel inside of it that gets rusty because of the water that is running through it. The turbine will have to be replaced an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have the ultimate g kirby. the green the brush doesnt spin when i turn it on and the belt is on correctly. whats the problem

You will find videos at this site that might be of help to you.\015\012\015\012http://www.kirby.com/Portals/0/videos.html\015\012\015\012If the brush does not spin you probably should remove it and clean well. Also, on each end of the br ... Kirby Ultimate G Bagged Upright Vacuum

I have a eureka 4351 and I think the belt is broken but I can't figure out how to access it to check. Roller brush doesn't spin though. Just need to get the silly thing apart.

... Vacuums

I have a bissell momentum ive broken 2 belts the brush doesnt seem to be spinning they are placed into the side slots correctly what could be the problem?

Most likely your brush needs to be removed and cleaned.\015\012Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn free ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

My problem is the brush on the bottom is not spinning and i think there is no suction from the bottom of the vacuum my rugs are in need of a vacuum and i 'm not sure what is going on - also nothing is going into the canister

Is there a shaft driving the brush, or is there a belt on this one? Are they intact and working properly? It could be possible that the motor isn't moving which would cause no suction or brush movement. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My kenmore progressive canister vacuum brush won't spin. I've checked the belt and it is fine. I've hit the reset button and there doesn't seem to be a problem there either.

... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

No Suction Something made a pop and my dirt devil featherlite is not sucking anything up. The roller brush is still spinning and the belt is good. What's the possible problem?

It is probably the dirt fan. u may have to get it serviced ... Dirt Devil Featherlite Bagged VacuumVacuum

I have a Dyson DC14 and the brush does not spin but the belt is still in place. how do i fix this problem?

Call dyson they will help you reset the vacuum //\012\012it has a reset bottun on the right side\012\012\012hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson dc-07 makes a loud grinding noise only on the carpet setting.The belt seems to be fine,and the brush spins normally.Do I have a potential clutch or motor problem?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0712 seconds