Having problems with your Hoover F7431-900 SteamVac Vacuum ?

How do you get the tank valves out of Hoover F7431-900? Does it take a special tool?

Answers :

Pull down firmly on valves they will come out (soap or water side) then firmly push new valve in. By design valves are self sealing to plastic tank.
Repair Help & Product Troubleshooting for Hoover F7431-900 SteamVac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you get the tank valves out of Hoover F7431-900? Does it take a special tool?

Pull down firmly on valves they will come out (soap or water side) then firmly push new valve in. By design valves are self sealing to plastic tank. ... Hoover F7431-900 SteamVac Vacuum

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not

Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. Thanks

Hoover Steam Vac V2, Model #F7430-900\015\012I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. ... Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet

Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Steam Vac clean water tank valve leaks

A) make sure that there is not a place for a stair attachment. If\015\012there is make sure air is not leaking through where the attachment goes\015\012on because of damaged or misplaced fitting.\015\012\015\012b) some steam ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Replacing valve on water tank on hoover steamvac

Buy the whole tank not worth the time to repair the valve ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and

The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac F7226900. Bottom of clean fill tank cracked, how do I take off the black plastic piece around the bottom of the tank without breaking it? Thanks!

Try this link belowhttp://www.ereplacementparts.com/hoover-f7226900-steamvac-parts-c-37315_37419_202371.html ... Vacuums

Hoover spin scrub clean water dispensing tank. How do I replace the spring, seal and valve stem at bottom of clean water tank?

... Hoover SteamVac SpinScrub 50 Carpet Washer with Hard Floor Tool and Accessories

I have a Hoover steam vac Model #F5865-900. I am unable to have the cleaning mode change from tools to floor when lowering the handle release. I hear a click, but the indicator stays on tool. I need to know how to get to the assembly that controls the cleaning mode.

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have the Hoover SteamVac Dual Model F7246-900 Serial AA12.0. In the Clean Water Tank the small black plastic check valve leaks water as machine is in use even when the on-off switch is not on. Can I purchase a new valve?

... Hoover Vacuums

I have a 9300-1 bissell carpet cleaner and when i used it today the vacuum was not sucking the water up. i know its working because when i take the water tank off i can feel the suction from the valve that connects to the water tank. any suggestions...

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?

... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.

I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

Can I get a new clean water tank for my Hoover? After filling tank, as soon as I lock it in water poors out even before I can start cleaning carpet.

Take the clean water tank off, and look at the underside very carefully. This tank is made of a very thin plastic, and chances are, your tank is cracked or broken. Sometimes the valves fail as well. There is a new tank available, a single ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My brush is no longer working on my bissell healthy home vac. when i try to turn it on it makes a high pitched squealing sound. I'm pretty sure it needs a new belt but my husband is having trouble getting the vac. apart. He says you need a special tool to get the screws out of the bottom of the vac. Any advice? THANK YOU!

Hi,\015\012 According to Bissel, they should be standard phillips screws. Nowever - things change.\015\012This is a general guide from Bissel for belt change - \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My Hoover 97441-980 Dual Steam Vac won't hold detergent. The valve is bad. How can I get the old valve out so that I can replace it?

Just grab the valve stem with a pair of needle nose pliers and pull it out, then you can gently work out the outer valve with the pliers, and then remove the gasket. The older tanks tend to crack around the valve which may be the whole problem, but t ... Hoover Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed

It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

Belt replacement Does Hoover Windtunnel V2 model # U8148-900 even take a belt? The owner's manual only describes how to change belt in powered hand tool, not the vacuum itself.

No belt- it is motor driven. what happens to these if the rollers get stuck(by- say, a Lego® or something)  is the roller itself has an insert which will break, requiring roller replacement. \015\012\015\012simple fix, but costs a ... Hoover WindTunnel V2 U8148-900 Upright Vacuum

I have a Hoover SteamVac Spot/Deep Cleaner, model F5515. I've had it a little over 1 year. It will not extract dirty water from the floor. I've made sure the recovery tank is attached correctly and also that the stair tool is connected. Is there something else I can try??

... Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1189 seconds