Having problems with your Hoover F7431-900 SteamVac Vacuum ?

Hoover turbine replacement

\015 Im looking for directions on how to replace my brush turbine on my Hoover SteamVac Dual V F7431-900. My brushes stopped spinning and I believe this is the problem. Thanks\015

Answers :

First you must remove the dirty water tank then the nozzle window on top of the machine. (this is the clear piece that the dirty water is sucked through.) then remove all 8 screws from the bottom along with the 1 screw on the main housing. after all this the top housing will be snapped into the base at two spots in the rear of the upper housing. when these are loose the housing should be out. you will find the turbine in the front along with 2 more screws and 2 hoses that also must come off. attach new part and reassemble.
\015\012good luck!!!
Repair Help & Product Troubleshooting for Hoover F7431-900 SteamVac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover turbine replacement

First you must remove the dirty water tank then the nozzle window on top of the machine. (this is the clear piece that the dirty water is sucked through.) then remove all 8 screws from the bottom along with the 1 screw on the main housing. after all ... Hoover F7431-900 SteamVac Vacuum

Replace turbine or control switch for Hoover F7412-900?

... Hoover F7412900 Upright Vacuum

How to replace turbine on hoover steamvac - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Replacing turbine on hoover max extract

... Hoover F7431-900 SteamVac Vacuum

Remove and replace turbine for brushes in hoover f7425-900

... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

How to replace turbine gear on Hoover model F7425-900?

... Hoover Vacuums

How to replace turbine gear in F5915-900 - Hoover V1 SteamVac SpinScrub Vacuum

... Hoover V1 SteamVac SpinScrub Vacuum

How to replace the turbine in a Hoover SteamVac F7458900?

Go to the link below for instructionshttp://www.youtube.com/watch?v=QBtWcC4gqjY ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

I need to find a replacement turbine for a hoover model # F7450100 carpet cleaner

Go to www.repairclinic.com and buy itGod bless you ... Vacuums

What does it cost to replace a turbine? - Hoover F5906-900 Upright Steam Vacuum

Hoover carpet cleaners don't have turbine persay. Do you mean extraction pump or brushes? ... Hoover F5906-900 Upright Steam Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman

\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How Do I Replace/Install the Hoover SteamVac Replacement Turbine Brush Gear Part # 91001019, 43191006, 91001097 - Its for a F7425-900. Is There a manual?

... Hoover V1 SteamVac SpinScrub Vacuum

Replace a turbine and gear assembly on a hoover F5914-900

... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Have called hoover about brushes they are saying that it is the whole motor and would be cheaper to by a new machine altogether. What do you think? Can just the turbine be replaced and if so what is approx cost? Is this something I can do simply by myself? If so how? thanks so much, Mel

You can get just the turbine. You would have to take the top cover off to do that. They are I believe around $50-$60 for one. Take the brush block out, then remove the screws from the bottom. There will be 2 long screws, they go into the turbine. ... Vacuums

Hoover steam vac all terrain turbine gear assembly

Hello,\015\012\015\012I'd be happy to walk you through this repair. Unfortunately this is a very common problem with the Hoover SteamVacs. \015\012\015\012Here's what you'll need to complete this repair:\015\012- ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray

This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy

Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Replace turbin Need to replace the turbin

This video will help you ... Hoover F7452-900 SteamVac Upright Vacuum

Hoover steam carpet cleaner - turbine needed for F7458-900

Once you get the turbine out, open it up by unlatching the three latches and unscrewing two screws. Pull the gears out and WD40 everything. Let it sit for a bit and start turning the solver gear at the back with a pair of pliers. Once it is loose, pu ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.

The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

I was using my Henry Hoover as usual. When i sucked up quite a fair sized puddle of water. The hoover instantly cut out and a strange burning smell was coming from it. Would this be the fuse, motor etc ? Or would it be worth my while just replacing the entire hoover ?

Hi. I have to wonder why anyone would **** up a puddle of water with a dry vacuum cleaner (with no earth lead). I realise that your question may simply be a joke, but if you are serious, I think it is probably fair to assume that it is now dead and p ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0590 seconds