Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

The brushes are not spinning at all. I have checked them and they are snapped in securely. It was working fine last time I used the machine. I have cleaned them and they spin manually just fine.

Answers :

You probably got a piece of foreign material jambed in there for a moment and it "smoked the belt" that spins the brushes,it will either have the belt on either side of the brush housing cylinder or like kirby vacs the belts around the cylinder and if broken it will be hanging there.good luck
Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes are not spinning at all. I have checked them and they are snapped in securely. It was working fine last time I used the machine. I have cleaned them and they spin manually just fine.

You probably got a piece of foreign material jambed in there for a moment and it "smoked the belt" that spins the brushes,it will either have the belt on either side of the brush housing cylinder or like kirby vacs the belts around the cylinder and i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac

... Vacuums

No manual Hi there my bissell will not **** up the water its been some time ago that I used it and it has not been used more than 2or 3 times can any one help me with this. I have also miss placed my manual and instruction this does not help me either .So if any one can help Id be a happy woman with clean floors thanx Vickie

Link to the manual download - http://www.bissell.com/Product_Search.aspx?Criteria=1699\015\012CHeck to see if the front of the unit is clogge ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.

First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

My bissell proheat 2x carpet cleaner is not spraying from the bottom or sucking up when turned on. The hand tool works just fine. I have made sure it was on floor cleaning when I used it to try and clean my carpet. the busshes are working but nothing else is happening this cleaner is about 21/2 years old and has only been used maybe 5 times so it has not had alot of use.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover Wind Tunnel that has been used twice both times at Christmas to pick up pine needles. It really has never been used because my cleaning ladies come every week and use their own machine. The problem I have is that the machine just doesn't pick up anything. Can you help. It's not overuse that is the problem!

You may have the ductwork of the cleaner plugged up with the pine needles. First, unplug the hose from the cleaner and find if you have suction into the bag. If so, check the hose and ducts for blockage from the pine needles. ... Vacuums

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine

... Bissell 8910 ProHeat Clear View Upright Vacuum

I have 2 coleman with double mantle. I have only use it 3 times since I bought it. Since then, I am unable to make both of them start. I have used locally sold petrol. I am wondering whether it is due to the poor quality of petrol or not. In the beginning, I tried to start it with alcohool since I did not know what kind of fuel to use. On the manual, it says that we have to use a special kerozene. But people familiar to Coleman lamp say that petrol should be fine since our old parents hav

If kerosene is specified then because it is a less volatile fuel it wil worrk better just as when you used alcohol.\012Petrol is too volatile and might not work well as the kerosene design is on a different grade and specific gravity.\012 ... Coleman Vacuums

Just bought and used the Hoover MaxExtract 77. First time the water was extracted from the carpet. Second time NO water in tank. Now I have wet carpet. I've taken the machine apart 3 times and cleaned the filters and still the water is not extracted from the carpet.

... Hoover F6055-900 SteamVac Maxextract LS Wet/Dry Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

There was no category for sewing machines....so I picked small appliance. When I depress the foot control E1 flashes on the LCD screen. I've followed the steps in the manual but it continues to flash E1. The machine will not operate. This is a brand new machine. I've used it only 3-4 times in the last 2-3 years. It worked perfectly until now.

What make and model of sewing machine do you own ? the more information you provide the easier it will be to assist you . ... Vacuums

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the

I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

Hi, I have a Hoover windtunnel t series vacuum. It was working fine until the last couple of times I used it. It just does **** uo the dirt. It **** a little, but not as strong as it used to be. Already checked for clogs (didn't find) and cleaned it and still doesn't work. Any ideas? Thanks!

This model, along with some similar ones, has been recalled. Stop using immediately. See the following site for information.\015\012\015\012 ... Hoover UH70205 WindTunnel TSeries Rewind Plus Bagless Upright Vacuum

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.

Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hello, I have a Viking Topaz sewing machine, the top thread is visible on the underside of fabric, indicating a tension problem. I have cleaned the machine, turned it off and back on, rethread it numberous times and tried to manually correct the tension. but nothing helps. What am i missing? Thanks

Thread, Tension, Needle. Make sure your needle matches your application. example: heavy denim needs a heavy needle (90-100) instead of the "universal" needle that usually comes with a machine. Also make sure that when you ... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Cleaning Solution It really isn't a mechanical problem. I would like to know what kind of solution I need to put into my machine. I bought it used and if didn't have a manual and I can't recall what I was told to put into the machine. I hope someone can answer my question. Thank you in advance Phyllis Woodall.

Most any brand name carpet cleaning solution will work. I like ZEP from the Home Depot. Nice fragrance, low foam and economical vs. Bissell, Hoover, other appliance brand names. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Nothing happens when i turn on my vax 6131. The machine worked fine last time used and the fuse is fine.

... Vacuums

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

No spray I have a proheat cleaner. The problem is there isn't any solution when I press the trigger on the handle to use the machine to clean a whole carpet yet if I use the handheld unit it works a treat. I have tried all the remedies in the manual.

\015\012Here are 3 common things that causes this problem:\015\012\015\012• clogged spray tips \015\012• defective solenoid valve in the base \015\012• defective trigger microswitch in upper handle ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web

(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

This was my grandmothers machine and when she passed there was no owners manual so I am not sure how to use the settings on it or oil it properly. I so want to use it cause it was hers but don't want to mess up the machine. She never even got a chance to use it before she passed away. I just have no owners manual. I know how to use sewing machines but this one is older and I don't want to mess it up. this was passed down to me. and a manual would help in so many ways. even if it was sent in a

May I get the manke and model # so I can help you more ... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Shop Vac was working fine last time I used it. Now I try to turn it on and nothing. I have cleaned the terminals on the toggle switch. I know there is power to the switch

Try tapping the motor area with a piece of wood or something, damp usage may have seized it up a bit ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0816 seconds