Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?
Floormate does not disperse wet cleaning solution on the floor. brushes and vacuum pickup all work
First check to see that the wheel assembly is not broken. The assembly must move correctly to allow the fluid to be dispensed. Check for breakage at the rear of the wheel assembly where it attaches to the base. If this is not the problem, you may have a defective soap tank.
Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Floormate does not disperse wet cleaning solution on the floor. brushes and vacuum pickup all work
First check to see that the wheel assembly is not broken. The assembly must move correctly to allow the fluid to be dispensed. Check for breakage at the rear of the wheel assembly where it attaches to the base. If this is not the problem, you may hav ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
Water and cleaning solution not dispensed when pressing the switch. Heat light is on, water and solution containers are full, brushes and vacuum working. Selector is on floor clean and not brush clean.
Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!
Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums
MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900
This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?
Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net
What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.
Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums
Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?
Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum
The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.
I'm having the same problem. The bottom plate is not level with the floor unless the vacuum is nearly in the upright position. Its like there should be a spring pushing the bottom plate towards the floor. Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The vacuum works on carpet mode but not floor and only when the wand is attached to the floor brush otherwise it does not work at all
Please define "works" on carpet mode" do you mean when you say it does not work at all, that it does not run, or does not have suction. This sounds like the symptom of a clogged hose with blockage like this another vac needs to be used to draw ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.
Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?
Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum
Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy
Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum
Henry brushes seem to catch in the carpet when pulling-will the brushes soften and make it easier to use as it makes the head bounce of the floor a bit when pulling making it harder work to vacuum?
There is a "see-saw" type switch on top of the cleaning head (the part that you push across the floor). This raises and lowers the brushes according to the type of floor you are vacuuming. Move this switch to the other postion and you will find that ... Henry Vacuums
Why does my Dyson Animal Upright Vacuum power light turn red when I tilt it back to vacuum? It will work if I switch it to bare floors and don't need the beater brush.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I replaced the beater brush and works on carpet but when I turn the beater brush oof to do floors, the vacuum shuts off.
... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R
Just purchased Floor Mate. It will not dispense cleaning solution. It will pick up water on floor and vacuum. Brushes rotate, no other problem.
Either a problem with the valve at the bottom of the tank, or where it sits is called the reservior asm, a rod in the handle hits to release the water, so your problem could be in that area. But you have a years warranty on it, take it to a warranty ... Vacuums
G5 vacuum won't start (turn on) when I try to use the accessory hose. It starts (works fine) when using the regular floor brush for vacuuming.
... Kirby G5 Bagged Upright Vacuum
I have a Hoover S3630 canister vacuum and the brush works on the bare floors but will not work on carpets.
Does your vacuum have an adjuster knob on the front? if so try raising the unit so that the brushes don't bind up on the rug and burn out the belt ... Hoover S3630 WindTunnel Bagged Canister Vacuum
I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Hoover tempo It will still **** through the hose but not from the brush-bottom. Can't find a reset button. Vacuum was GREAT and is only about three weeks old. I know it still works because it has plenty of strength through hose, but won't pick up when rolled across floor. thanks! Marian
Sounds like a blockage or belt off in the foot of the vacuum. there is no reset button on this model. ... Hoover Tempo Widepath Upright Vacuum - Blue
The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new
Sounds like there is a clog..\015\012\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..\015\012\015\012Or a clog could be in the vac close to where the hose conects to the v ... Hoover U5269910 Bagless Upright Vacuum
I have Dyson DC15 ,Brush not working - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I have a hoover savvy that the rollers wont turn. I've taken it apart to make sure the brushes are not caught but nothing happens. I only used this vacuum once. It was a floor model when purchased. I just need to figure out what I need to do to get this to work.
Hi there SmartAlec from NelsonVacuums.com.au here. I have to say that if it is not as simple as a belt - I assume that when you checked that the brushes weren't caught that ... Hoover U8125-900 Savvy Bagged Upright Vacuum