Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


Answers :

I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot where the pieces join and made sure it was real tight. This seemed to fix my problem (until the wire tie starts to wear out and stretch at least)
Make sure you REALLY pull the lever controlling the brush spin all the way up. On mine I REALLY need to force it to the top. If I don't use enough force and it's just a tiny bit below the top, the brushes continue spinning. I wish it was easier to flip from one mode to the other but mine has always been "stiff". Hope this helps. It took me a while to figure it out. Once you get the hang of using it, it works GREAT!
Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

I have a broken handle for kenmore vacum cleaner model 116.33921300(beltless). I ordered and already got a new handle. I'd like to know how I should deassemblel and put togetger old element to a new handle step by step. Could you help me?


First you have to get the headcover off. After that use a butter knife and/or flat head screwdriver and press forward on the four tabs that retain the pedal. Old Handle just prys off, a new one will press on. ... Vacuums

The vacuum stopped working when i was vacuuming. The bag had a hole in it so all the dirt and stuff where clogging the filters. I cleaned them and put a new bag in but it will not turn back on. So I want to take it apart to see if there is more dirt on the inside,


... Fuller Brush FB-PT2 Vacuum

I just received My brand new hoover platinum lightweight upright UH30010 (with canister) which I ordered through ebay and today is just the SECOND time I used it but the check bag light indicator is already flashing. My husband and I live in a 1 bedroom (695 sq t) apartment (no kids or pets). I checked the bag and the dirt is just maybe two inches - far from the limit line showing on the bag..and I remembered the advertisement on TV that it can even last upto to six months depending on the usage


I have the same problem. If it was just an indicator light I could live with it, but mine actually shuts the vacuum off. I can only run the vacuum for 3-5 seconds before it turns itself off. Any ideas? ... Hoover Platinum Collection Upright Vacuum

My Eureka Atlantis Express is brand new - never used. I took it out of the box, read the manual, filled the soap and clean water tanks, put them in. I lifted the machine off the counter to take into the living room but all the water came running out of the bottom all over the kitchen floor. I can see where the little white plastic piece sticks up into the water release valve and lets the water out. How do you stop this? Can it be fixed?


... Eureka 2553A Atlantis Handheld Wet/Dry Vacuum

Roomba wont stop going in circles,code 9 comes up, cleaned front caster wheel to no avail. 500 series roomba. called company said we need a new one, if this is the best we can get out of a roomba they are junk.


\015\012\015\012Your bump sensors are malfunctioning. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great.. ... iRobot Roomba 560 Robotic Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Hello, I have an Electrolux vacuum. In desperation, I vacuumed up some water and my machine stopped. I am hesitant to take the machine to a repair place for fear that if it is a simple repair they will not be honest. Can anyone give me advice on whether this is a problem that requires a new motor or major repair? Thank you!


Although it's never to be recommended, it is sometimes possible to vacuum up a little water without doing significant damage. However, the fact that your machine then stopped suggests that the electrics got wet. That may or may not have caused expens ... Vacuums

The brush spun for a second then stopped spinning, it snapped one belt already and it was brand new. whats going on?


Either the bearings on the brush are siezed or you caught the belt when you put it back together again ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Vax 6131 water pump had stopped working on taking apart it had over heated and plastic casing had melted in one place,obtained new pump from buy spares which matched old part fitted and reasembled but pump does not run ,is there any internal fuses ? Or any thing else to replace


... VAX Appliances Vacuums

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.


I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

The brush vibrates for 30 seconds, then stops. If I depress the on/off button a couple of times it strats again, but stops after 10 seconds, and so on continously. It does it too with a new brush and with a new toothbrush.


Your battery is not getting charged properly, mabey you need to clean contacts or the life of the batterys are over ,time for new ones, if they are replaceable if not fork out for a new unit. ... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Ordered I put all my parts in zip lock bags, number them in order. Then hopped online and ordered the turbine. should be here is a few days. Thank god this info was out here when I googled it. I probably would have thrown the machine out and bought a new one. Thanks, Karen


Happy to help ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

New battery!, roomba runs for 5 - 10 seconds, stops, starts running, stops, runs, stops, then beeps and low battery flashes. Have taken battery out, held start button 20 seconds, replaced battery and directly connect to charger, 72 hours min., still same problem.


... iRobot Roomba Discovery SE Bagless Robotic Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.


How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

My Model 2961 Eureka wont take power now?


Hi,Anytime that you smell that electrical burning smell on a vacuum cleaner, this is the motor going bad. There are two distinctive burning smells in fixing vacuum cleaners, the electrical burning smell which is the motor, and a rubber ... Eureka 2961AVZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds