Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

Replace hoover floormate 3000 seal, spring, valve stem


Answers :

Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace hoover floormate 3000 seal, spring, valve stem


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover spin scrub clean water dispensing tank. How do I replace the spring, seal and valve stem at bottom of clean water tank?


... Hoover SteamVac SpinScrub 50 Carpet Washer with Hard Floor Tool and Accessories

I need to replace the torsion spring on to the valve arm that controls the valve door. I just need a explanation as to how the spring is connected to the two parts. This is for a Hoover U6632900 upright bag-less series.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. Thanks


Hoover Steam Vac V2, Model #F7430-900\015\012I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. ... Vacuums

How to replace a valve stem - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How to replace the torsion spring on Hoover WindTunnel model U6630-900


... Vacuums

Valve Stem Assembly for Hoover Steam Vac


Put the rubber seal on the bucket first, then put the spring on the valve stem, slip into the hard collar, then push it into the opening in the seal, it will snap into place. ... Vacuums

Hoover Steam Vac clean water tank valve leaks


A) make sure that there is not a place for a stair attachment. If\015\012there is make sure air is not leaking through where the attachment goes\015\012on because of damaged or misplaced fitting.\015\012\015\012b) some steam ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover SteamVac Is there a spring in the trigger. The valve was is two pieces and we glued it together and it still won't retract. Is it possible there was a spring in the trigger that got lost or do I need a new valve? redevil16 helped me last time. Hopefully he or someone can help. Thanks, Sandy


I'm not sure what your referring too, but Here is how it works. The trigger is snapped into two "rocker retainers" in the handle. when you pull on the trigger, it rocks and pushes on a rod that goes down to another shorter rod and that one pushes on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed


It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

How to replace the torsion spring on my Hoover WindTunnel model U6630-900


... Hoover Vacuums

I have a hoover u6630-960 wind tunnel. How do you connect the torsion spring valve arm part # 38358001 with the valve arm rear - ag part # 3871948 Thank you


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Hoover 97441-980 Dual Steam Vac won't hold detergent. The valve is bad. How can I get the old valve out so that I can replace it?


Just grab the valve stem with a pair of needle nose pliers and pull it out, then you can gently work out the outer valve with the pliers, and then remove the gasket. The older tanks tend to crack around the valve which may be the whole problem, but t ... Hoover Vacuums

Replace the wheels and spring on a hoover 12 amp vacum,have the assembly can't figurew out how spring goes on.


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Our hoover F7220-900's solution tank's spring came out? Does this mean I have to replace the top clean tank or can I replace the sping?


You will need the valve assembly. as long as the hole that it mounts in is not cracked or broken. ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac


Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacing valve on water tank on hoover steamvac


Buy the whole tank not worth the time to repair the valve ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

How do i replace the spring support for hoover nano cyclonic?


... Vacuums

Replacing leaf spring Hoover wheels


If people are still having this problem, please post here and I will take a picture of the correct placement for the metal clip. ... Hoover U5227-930 Elite Upright Vacuum

Valve stem assembly


Put the rubber seal on the bucket first, then put the spring on the valve stem, slip into the hard collar, then push it into the opening in the seal, it will snap into place. ... Vacuums

Hoover Floormate H3000 replace water intake hose


I have the same model with a broken water recovery hose. I can tell you how to get the old one off. Would you tell me Hoover's name and part# or item# for the part? I'm not sure I have found the right name or part number to order... \015\012 ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

How to replace the tension spring on a hoover 5454 wind tunnel


... Hoover U5454-900 WindTunnel Vacuum

My Hoover Decade 80 has started to blow dirt out around where the dust cup fits when I turn it on. Is there a seal that I need to replace?


... Vacuums

I have a Hoover U5750 Windtunnel vac. I had to replace the front wheel assembly and don't remember where/how the torsion spring goes.


... Hoover Vacuums

My Hoover floormate motor started smoking. It is over 9 years old. I keep the floor brushes clean. I am wonder if replacing the mother is worth it.


MSRP on this motor is $69.95. Labor may be another $30.00. I often see these units in thrift shops, which may be worth a try. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds