Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

Hoover floormate h3044 brushes stop working

\015 Brush motor has been replaced 3 times.\015

Answers :

Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover floormate h3044 brushes stop working


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover nanolite power brush stopped working


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover Steam Vac Ve brushes stop working - Hoover F7431-900 SteamVac Vacuum


Hi There,\015\012\015\012You'll need to try and diagnosis what is causing the brushes to stop spinning first. A lot of the times this can just be caused by debris stuck in the brushes. I have written a in-depth repair solution on how ... Hoover F7431-900 SteamVac Vacuum

Hoover F7412-900 brushes stopped working - Hoover F7222-900 SteamVac Upright Vacuum


... Hoover F7222-900 SteamVac Upright Vacuum

Hi the turbo brush with my new hoover whirlwind has stopped working. the suction on the appliance is fine and there are no blockages. have tried cleaning the head but it is still not working. any ideas//


... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

The wet pickup and the dry pickup switch on my Hoover Floormate have stopped working. Only the scrub cycle works. Needless to say, it will not pick up wet or dry. Can you tell me what the problem may be and how to repair it?


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Deluxe Elite Rewind vacuum has stopped working as it should. The airflow indicator snaps on almost immediately after I turn it on whether the hose is connected to the brush or not. There isn&


... Hoover Elite Rewind Bagless Upright VacuumVacuum

Brush stopped working on Hoover 5906-900


This is how you fix the hoover (F7452-900)" Brushes not spinning"Uses the turbine model and same solution would be similar.The main gear attached to turbine becomes stuck. This problem sho ... Hoover F5906-900 Upright Steam Vacuum

I have a hoover windtunnel upright vacuum bought it a few months ago and now the brush spinning stopped working.


You probably have a broken belt, or the belt came off. The Self Propel Windtunnel has an issue with the pulley that tightens the V-belt in place getting stuck and needs to be taken apart and released, but most l ... Hoover Vacuums

My Hoover nano brush has stopped working. This happened when we first bought it and the problem fixed itself randomly. Now it's happening again. Any help?


Unplug the unit for twenty minutes in case it had overheated. If when plugged back in, it will not run, then it will require disassembly to determine failure cause (motor, cord, switch, or TCO) ... Hoover U57009RM Vacuum

Brushes stopped working - Hoover F6207-900 Steam Cleaner


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F6207-900 Steam Cleaner

I have a Hoover Bagless Upright with twin chamber systems and it just stopped working while I was using it. I checked the outlet, brushes and belt and everything looks fine. It will not start up again


... Vacuums

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.


... Hoover F5826-900 SteamVac Upright Wet Washer

Brush on my hoover z400 bagless upright stopped working. Model # u9125-900


I think that machine needs to be in the reclined position for that brush to turn on. It its not that then, you probably just have a broken belt. ... Hoover Vacuums

Hoover floormate Water will not come out-brushes move-suction works-just no cleaning solution--help!!


It seems to be a common problem with this series of floormate... some home quickfixes (a hassle, i kno) but put downward pressure while using the solution.... Check your warranty that came with it, and how long you purchased the floormate... Alot of ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!


Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Hoover Floormate H3000 stopped working during usage. Took fill take and solution take off to allow vacuum to dry fully. Still did not turn on. Any ideas would be great!


If it doesn't turn on at all, then you may have a bad switch, cord or motor. ... Vacuums

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow


The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0701 seconds