Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

Wet pickup has no suction. Dirty water stays on floor. I tipped it over and held a tissue in front of the wheels to see if the Floormate had any suction whatsoever; it does not. What now?

Answers :

Okay, I too had the same problem with the water. I read that darn manual again and realized that I hadn't clicked the filter cover on tight. Wallla! The tank fits better and it works like a charm! Who knew?
I would try replacing the filter first. That seems to be the most common problem when you have no suction.
Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wet pickup has no suction. Dirty water stays on floor. I tipped it over and held a tissue in front of the wheels to see if the Floormate had any suction whatsoever; it does not. What now?

Okay, I too had the same problem with the water. I read that darn manual again and realized that I hadn't clicked the filter cover on tight. Wallla! The tank fits better and it works like a charm! Who knew? ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Floormate not suctioning water back up

I love my floormate so muck that when my first one stopped vacuuming, I bought a new one - just figured it died. Then my new one worked well until one day, it suddenly stopped.\015\012\015\012I discovered that the filter attachment holde ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?

Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

The vacuum i've had for 6 months has very liittle suction power. checked that the belt is on. cleaned filter. checked to see if hoses were clogged. I used a super vac to suction any debris out of vacuum. still little suction power

As this unit has 3 filters on it, a lot of people forget about the one filter that will cause all of your trouble here. \012\012There is the exhaust hepa filter, no problem, your unit is pretty new, it shouldn't be a problem. \012Th ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?

... Vacuums

Dyson hose suction strong...when using the brush bar no suction available. Have looked to see that all airways (u-bend) are clear. When engaging the brushbar the brushbar turns but no suction to floor.

Hello,There\012 are several things that this could be. Probably the most common problem\012 that we see when customers come in with this problem is actually a \012fairly simple problem to fix. Here are just a few things that this could\01 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No suction. I have followed the detachable parts no suction. I have followed the detachable parts and it seems to have suction through to the base but doesn't pick up anything significant. I have looked through the hose connecting the base but I can not see anything obstructing it.

Poor suction can be caused by obstructions, poor air flow or a compomise in the air flow (hole in the hose). Since you have started with that I would next look at all filters and clean them. First check for suction at the motor, then at accessory hos ... Vacuums

I have a DC17 which is only one year old. Today I lost suction and called for assistance. A Dyson technician told me to pull off the wand and see if it is clear. It was clogged so cleared out the obstruction. My filter was cleaned more than 24 hours ago. The vacuum still has no suction. Is it dead, any other suggestions. Please help.

Take the hoses off and give them a good shaking.\012or get a long piece of stiff wire and gently poke through the obstruction. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I don't get much suction from the hose on my DC17 All Floors. I don't see any obtacles in the hose. The suction when upright is fine.

Hello,The way your Dyson DC17 is designed, there is a suction divert mechanism that diverts the suction to floor when the vacuum cleaner head is pushed down, and then back to the hose when the vacuum is in the upright position. If you a ... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.

If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

My Oreck UP350 has no suction -- I've made sure everything is cleaned out (filters, etc) that I can readily see that has to do with the suctioning process, but now instead of picking up the dirt it keeps dumping the dirt and trash on the carpet. I am at my wit's end!

... Oreck Vacuums

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.

If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

No suction I've only had my vacuum for a couple of months and it seem I have a similar problem but there is no clear blockage. It seems like I don't have adequate suction that reaches the accessory hoses nor the main one. I'm not sure where to start. I've taken the darn thing apart but I can't see any obvious malfunction. Any suggestions?

If you have low suction at the end of the hose, then you either have a clog in the hose or a clogged filter. Take the hose off and drop something in it to see if it comes out the other end. If you have suction at the end of the hose, then the dirt ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Suction perfect when in upright position, but when tilted to actually clean there is total loss of suction - cannot see blockage anywhere. Thanks for your help.

If you are confident there are no blockages, look underneath, where the brush is, and you will see a short length of reinforced clear plastic hose. This often develops a split which results in loss of suction. You can pull the hose off at the motor e ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.

Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums

Low suction I have an Electrolux central vac that is approx. 11 yrs old. the suction is very low. this started about 1 week ago. I checked the hose and it is clear. I also went into the attic and checked the pipes(as far as I could see them) and they appeared to be intact.

1) Have you checked the filter? If it is clogged your suction will be low. Also, you could have a pipe loose where you can't see. Make sure that you can get a coin to go all the way through the hose. make sure the suction motor ( the unit ) is coming ... Electrolux Central Vacuum

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe

I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

No Suction The water/soap solution dispensing just fine but when I pull the machine back over the water solution, it is not being sucked up (usually it is easy to see as it you can see the water being pulled up through the clear plastic)

It sounds like the lint filter is clogged. It is located on the top clear plastic piece (the one with the dial to switch from floor to tool use) and is on the underside. It is a small (1 inch square) red plastic piece with a little door on it. Fli ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No Suction Hoover H3000 floormate does not have enough suction. Brushes and squeegee recently replaced. No Clogs: filter and tank are clean.

The water channel hose could be torn. you can check by removing the lower tank and tilting it backwards, it is located in the lower section. could also be the filter cover. it is needed for full suction control. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?

The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

Roomba circles My Roomba circles for a few minutes, then beeps 9 times and stops. A red exclamation mark appears on the left hand side of the controls. If you persist in restarting it, eventually I have been asked to clear Roombas wheels. As far as I can see, there isn't anything blocking the wheels.

Yes, this is known issue and if your bumper moves freely, you might be facing a sensor fault caused by poor quality of components.Here is a guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave fun ... iRobot Roomba 560 Robotic Vacuum

My floormate is not suctioning very well. Tech support told me to take out the brushes and put them back in and this helped for a little bit then it went back to not suctioning. deb

When you took the brushes out, was there hair wrapped around them? Sometimes they just need to be cleaned off. When you take them off, there is a belt they connect to that also goes around a gear -- make sure the belt and gear don't have hair wrapp ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0664 seconds