Having problems with your Hoover Floormate H3000 Upright Wet/Dry Vacuum ?

Hoover Floormate H3000 replace water intake hose

\015 Ordered the part can't figure out how to take it apart to replace the part!\015

Answers :

I have the same model with a broken water recovery hose. I can tell you how to get the old one off. Would you tell me Hoover's name and part# or item# for the part? I'm not sure I have found the right name or part number to order...
\015\012
\015\012Remove the recovery tank. Remove 2 screws behind the recovery tank that hold a plastic cover on the collar connecting the recovrery hose to the "flat" plastic channel mounted behind the recovery tank. Remove the front nozzle and the brushes. Remove the grey outer cover from the top of the floor head section by prying upwardd on the front of the grey cover. Remove the plastic tie strap from around the recovery hose, water delivery hose, and the cable that runs up the length of the handle to the button that turns the brush motor on/off. I was able to "relaese the locking mechanism" on my tie strap and remove it so I think it is reusable, but you may have to cut/break yours then replace it on reassembly.
\015\012
\015\012Now you have to unhook the front of the wheel assembly so it will swing down out of the way. This will be easier if you set the Dry/Wet selector to "Dry Pickup". To unhook the wheel assembly: (1) Dissconnect the cable associted with the brushes by pulling the black ball on the end of the cable upwards and out of the small black rectangular plastic connector. You'll probably also have to pull the cable's outer sheath upwards out of the channel it rests in. (2) Look directly behind and below where that ball was connected to find a small black post around which an arm is fastened by an elongated hole on the end of the arm. This post is designed to "pop" in and out of palce. (3) Using something like a pair of needle nose pliers, pop the post out by applying pressure toward the side of the head that has the Handle Release lever. (Be carefull not to drop and loose this post as I almost did.) Now from beneath the head, with a little force and some wiggling you should be able to pull the front of the wheel assambly downward so it swings out of the way.
\015\012
\015\012The best way I can think to describe the next steps is if you look at the new part you'll see 2 tabs sticking down from the bottom of it with slots in them One tab hooks on a bump in the aqua colored plastic just behind the black Brush Motor housing and one hooks on a similar bump just forward of the Brush Motor housing. Looking at the head from the bottom, the rear tab is easy to see. To see the front one, look for a small slot in the aqua plastic. Reach a small screwdriver in from the bottom of the head and pry these tabs off the bumps while applying some pressure on the old recovery hose part (the rear tab goes to the rear and the front tab goes forward). I broke both tabs off my old recovery hose part and luckily didn't do much damage to the bumps. Once you release these tabs the part should be loose from the head.
\015\012
\015\012Now press the Handle Release to tilt the head down in a typical operating posoition and you should be able to pull the hose connector down off the "flat" plastic channel and out toward the front of the machine. If the new part does not come with a connector on the top end of the hose, you can unscrew the old connector from the old hose (turning the opposite direction of normal threads) and srcew it onto the new hose.
Repair Help & Product Troubleshooting for Hoover Floormate H3000 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Floormate H3000 replace water intake hose


I have the same model with a broken water recovery hose. I can tell you how to get the old one off. Would you tell me Hoover's name and part# or item# for the part? I'm not sure I have found the right name or part number to order... \015\012 ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

How do i replace the water channel/ hose assembly on a Hoover Floormate H3000 ?


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Floormate clogged water line - Hoover Floormate H3000 Upright Wet/Dry Vacuum


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Floormate--Does not pick up water. - Hoover Floormate H3000 Upright Wet/Dry Vacuum


First make sure that you are getting suction from the bottom of he machine. Most of the time the squeegee is worn out which does not allow it to pick up the water like it use to. Turn over the machine and inspect \015\012the squeegee. If it looks ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My hoover floormate will not dispense water - Hoover Floormate H3000 Upright Wet/Dry Vacuum


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My floormate isn't picking up the wet water - Hoover Floormate H3000 Upright Wet/Dry Vacuum


I have had same problem. Had to remove both clean fluid container and dirty fluid container. Had to put clean container in first then tilt back the unit using release pedal located bottom left. Then replace the dirty fluid collection container. They ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Floormate water does not come out - Hoover Floormate H3000 Upright Wet/Dry Vacuum


Check nozzle's are not blocked here is manual,http://hoover.com/file/682/ ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Floormate H3000-050 power head/taking apart


I didn't find this as difficlut as red devil 6, however, having 2 people helps. Remove the brush assembly using the 2 brush release buttons. Remove the front nozzel by sliding the 2 nozzel release clips away from the unit. Do NOT remove any screws ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

It wont **** up the water anymore - Hoover Floormate H3000 Upright Wet/Dry Vacuum


Its clogged or needs a new filter or its not sealing ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My floormate does not pick up liquid anymore, there seems to be no suction. I took it apart a bit to look inside and the short hose which goes from the intake area to the collecting bin is ripped and open. can this piece be replaced?


Hello,\015\012\015\012yes, the ripped part/piece can be replaced.\015\012\015\012Remove the ripped part from the device, take it to the market and use it as a sample to buy a new one. Fix it back into the device and that's all ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

No water when squeeze the buttom - Hoover Floormate H3000 Upright Wet/Dry Vacuum


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

No Suction Hoover H3000 floormate does not have enough suction. Brushes and squeegee recently replaced. No Clogs: filter and tank are clean.


The water channel hose could be torn. you can check by removing the lower tank and tilting it backwards, it is located in the lower section. could also be the filter cover. it is needed for full suction control. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

It will not **** up the water. - Hoover Floormate H3000 Upright Wet/Dry Vacuum


First make sure that you are getting suction from the bottom of the \015\012machine. Most of the time the squeegee is worn out which does not allow \015\012it to pick up the water like it use to. Turn over the machine and \015\012inspect \015\012th ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Not picking up dirty water off floor. - Hoover Floormate H3000 Upright Wet/Dry Vacuum


First make sure that you are getting suction from the bottom of the \015\012machine. Most of the time the squeegee is worn out which does not allow \015\012it to pick up the water like it use to. Turn over the machine and \015\012inspect \015\012th ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Hoover steam vac max - hose that sucks water up from carpet broke


... Hoover F6207 Steam Cleaner

How do i take apart my hoover floormate h3000


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.


Hi\015\012\015\012Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the ... Vacuums

My Hoover Steamvac Widepath will NOT pickup the water after dispensing. I checked the hose inside the cleaner, there was a cut in the hose so I put electrical tape and completely sealed the cut. Still will NOT pick up water. I can't find any other problems with the hose. Any suggestions?


HelloHere are some suggestions you might want to follow to solve this problemFirst double check if there are other cuts in the hose or any sort of blockage or clogging in the hose and be sure to remove any form of debris ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Replacing intake hose


Should be a clamp on each end to undo, then the hose will come off. ... Hoover Vacuums

Hoover floormate will not pick up water


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover floormate won't turn on - Hoover Floormate H3000 Upright Wet/Dry Vacuum


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Replacing wheel Hoover spirit vacuumm - Hoover Spirit Canister Vacuum Cleaner Non Electric Hose Canister Vac Cleaner Non Electric Hose


... Hoover Spirit Canister Vacuum Cleaner Non Electric Hose Canister Vac Cleaner Non Electric Hose
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0853 seconds