Having problems with your Hoover Fold Away U5162-900 Bagless Upright Vacuum ?

Need to replace belt


Answers :

Please go to this link on my business web site for instructions on changing your belt: http://www.sewvac1.com/Hoover_U5162_900.pdf
Repair Help & Product Troubleshooting for Hoover Fold Away U5162-900 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.

Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey

... Electrolux Vacuums

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt

On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?

Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym

Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01

... Vacuums

I need to replace a belt on the shark infinity pet care system upright vacuum. I have the belt I need a manual to show me how to put it on

... Euro-Pro NV31 Infinity Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Replace belt on eureka big boss sweeper. Bought sweeper got it cheap and it needs a belt. So i don't have anything to go on to replace it. Seems like there is a pulley below and not sure how to install

... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.

I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP

Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim

Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

If i need to replace belt do i need to replace anything else

Should say no ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?

Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I replaced the belts on my windtunnel vacuum u6439-900 cleaner..it works fine for a minute or so then it smells like burnt rubber and does not self propel. Does the v belt need to be taut or loose?

... Hoover Vacuums

I need to replace belt but can't find where belt belongs,only says belt access. can't find belt.

Not easy to read, but this URL might be of assistance to you:\015\012\015\012http://canada.bissell.com/images/UserGuides/9500_107.pdf\015\012\015\012Please let me know if it does not help you. My assistance is free and I am more than wil ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.

... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Replaced the belts on Saturday with belts that were purchased in 2003 but never needed. It is Monday and the small belt has already cracked and separated from the center fiberglass or whatever the band is made of. Is there any way to keep these belts from drying out in Alaska?

Hi Alaska,You can put a small amount of vaseline or a tiny bit of any oil on the back and ONLY the back of the belt Do not get any on the sides or inside of belt. Please be sparing with the oil.You can also put these in a zip lock b ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Need instructions on how to replace the belt on a hoover dirt finder model u5321-930

You can download the manual from the link below:\015\012\015\012http://www.hoover.com/Media/ModelPDF/U5468900.pdf\015\012\015\012Please update the question & let us know if the information given was useful to you - Good Luck! ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I need to replace the belt on my hoover fusion plus upright vac. But I cannot find what belt it takes. the number on the belt is worn off

Hello : \015\012\015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

I need to replace the belt I bought a new belt and I can't get the belt back on

On this pagehttp://www.totalvac.com/videos/kirby-vacuum-cleaners-videos.htmthere is a video at the bottom on changing belts on a Kirby ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2300 seconds