Having problems with your Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum ?

Hoover Fusion Cyclonic

\015 I was vacuuming and it just stopped. The filter is clean, there are no circuits popped anyone have a clue as to why it would just stop?\015

Answers :

Ok, lfitz, I fixed my problem. First I called the Sears Service Center. They told me that I would have to drop it off there, and they would send it to Orlando to get looked at. The whole process would take about 2 weeks and who knows how much money. So I decided to become my own Hoover technician. It turns out that my original diagnosis was right about the chord that electrically connects the power on/off switch at the top of the handle to the rest of the vacuum. This was extremely easy to fix so please don't be scared away, although it does require a little philips-head screwdriver action. As always, make sure the vacuum is unplugged before you start. On the back of the vacuum, there is the hook that you wrap the electrical chord around for storage (the top one). On either side of that hook are two screws. Unscrew those. Now, the small piece of plastic that has the hook on it can be carefully pulled back, or removed if you need to. Inside, I found the detached end of a coiled black electrical chord that looks kind of like an A/C adapter. This chord should be plugged into the bottom of the metal shaft that slides in and out to allow you to adjust the height of the handle. Now, adjust the metal shaft so that you can plug the black chord back into the base. Push the chord in until you hear it click. Now, put the plastic piece back in place and put the screws back in and you're done. Plug it in and give it a try. I hope this helps.
If you are mechanically inclined, you can disassemble the vacuum and turn it on, and carefully connect a voltmeter to the two wire leads going into the motor. If you get a standard 120 volt reading, your motor is shot, and will have to be replaced. Or if lucky, you might find a disconnected lead that can simply be re-soldered ( this happened to me once). Note that the Hoover Fusion motor has several design flaws and will eventually fail as a result of these flaws. Probably better to just purchase a new vacuum if the motor is shot.
Repair Help & Product Troubleshooting for Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Fusion Cyclonic


Ok, lfitz, I fixed my problem. First I called the Sears Service Center. They told me that I would have to drop it off there, and they would send it to Orlando to get looked at. The whole process would take about 2 weeks and who knows how much mone ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Loss of suction - Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum


Check the hose and plugged filters. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Hoover Cyclonic Fusion Vacuum overheats and shuts off.


If it gets too hot it will shut down for about an hour...it does that to protect the motor. A lot of tools and work appliances seem to have that feature nowadays. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Manual I was given a Hoover Fusion Cyclonic Filtration System. Can I Download a manual lou


Go to hoover.com, scroll down to downloads, enter your model number which is located on the metal tag either on the back or bottom. If it is available you will be able to download it. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

HOW TO EMPTY FILTER - Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum


Here is the manual > http://hoover.com/file/445/ enjoy ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

REPLACE BELT TO BRUSH - Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum


... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Hoover fusion plus cyclonic upright vacuum


While I'm having a different problem, the problem you guys are experiencing can easily be fixed by cleaning the two internal filters. My vacuum did the same thing, just stopped running mid-stream. Remove the main filter cup. Look inside the cavity of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Where can I get a filter canister door - Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum


... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Hoover Mach 3 (Fusion): Dirt Will not enter dirt cup


There is a filter in the top over where the dirt canister clips in, and one under the dirt cannister by the motor. Sometimes removing and cleaning will help if you have not tried it already. ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Hoover wheel assembly replace wheels - Hoover Fusion Vacuum Front Wheel Carriage 93001674


... Hoover Fusion Vacuum Front Wheel Carriage 93001674

Overheating Hoover My Hoover cyclonic 1800w keeps overheating and turning itself off, not sure if it's the filter, I've cleaned it but it didn't look very dirty.


Most likely caused by a lack of airflow. Check to see if you have airflow at the end of the hose. If not, Remove all of the hoses and ensure that they are not clogged. If there is airflow through the hose; check the air inlet immediately aft of the b ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

My Hoover vac, cyclone u5180-910w, has dog smell in the filter assy. Hoover does not have a manual nor solution nor do they offer a replacement part. Is this faulty design/negligence or do they really


... Vacuums

No power in my hoover uh70035b - Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum


... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Disassemble hoover sh40060 multi cyclonic - Hoover SH40060 Bagless Canister Vacuum


... Hoover SH40060 Bagless Canister Vacuum

Where is the reset button on hoover savvy - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Replace main body on Hoover U8144-900 - Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum


... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

How to change belt on hoover savvy vacuum - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


How do I change the smaller brush belt on a Hoover Windtunnel Cyclonic? ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Disassemble hoover savvy - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

How to replace the switch hoover UH70015 - Hoover UH70015 Bagless Upright Cyclonic Vacuum


... Hoover UH70015 Bagless Upright Cyclonic Vacuum

What's your problem?hoover dust manager cyclonic upright hoover wont pick up


A blockage from point of pickup to air filter ... Vacuums

Can not find a proper fitting v-belt to fit my hoover wind tunnel cyclonic. i even ordered it from hoover.


The correct belt is # 38528034 ( package # 40201200 ) This belt may seem loose when it is installed, because there is an "idler bearing" that pushes down on it when the handle is released and dropped back. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hoover smart cyclone cleaning instructions - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover remedy overheating - Hoover Remedy Multi-Cyclonic Upright Vacuum, UH70604


... Hoover Remedy Multi-Cyclonic Upright Vacuum, UH70604

How do I take apart the cyclone for the cyclonic Hoover? Uh70070, I would like to clean it.


Click the link below for manualhttp://hoover.com/file/560/http://hoover.com/file/560/ ... Vacuums

Hoover savvy reset button for brush roller - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0436 seconds