Having problems with your Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum ?

My hoover floormate h3060 has not been used for some time, when I went to use it, it would not dispense the cleaner..The last time I used it, I used a mixture of amonia and borax. I think the hose is clogged. What should I do??

Answers :

You most likely have either a clogged screen at the bottom of the fill tank or the jets that spray fluid are clogged. You can unscrew them and power a paper clip through them. If the hoses are by chance clogged which doesn't happen often, Pull one off at a time and blow real hard to unclog, then put it back on, then move to next hose.
Do NOT take all of them apart at the same time or they can get mixed up and it's a pain to figure out how it all went back together.
Repair Help & Product Troubleshooting for Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover floormate h3060 has not been used for some time, when I went to use it, it would not dispense the cleaner..The last time I used it, I used a mixture of amonia and borax. I think the hose is clogged. What should I do??

You most likely have either a clogged screen at the bottom of the fill tank or the jets that spray fluid are clogged. You can unscrew them and power a paper clip through them. If the hoses are by chance clogged which doesn't happen often, Pull one of ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi, I have a Hoover windtunnel t series vacuum. It was working fine until the last couple of times I used it. It just does **** uo the dirt. It **** a little, but not as strong as it used to be. Already checked for clogs (didn't find) and cleaned it and still doesn't work. Any ideas? Thanks!

This model, along with some similar ones, has been recalled. Stop using immediately. See the following site for information.\015\012\015\012 ... Hoover UH70205 WindTunnel TSeries Rewind Plus Bagless Upright Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web

(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Lost manual last time i used the upholstery tool and i think i forgot to put a part back on...from the floor head to the recovery tank the water comes up but i have a gap there...the water won't suck up off the floor...

Send your email address to [email protected] I found the pdf manual file for this unitl ... Hoover F5906-900 Upright Steam Vacuum

I recently purchased a bissell proheat 2x and have used it several times with great results, the problem I am now having is no water being released from the bottom of the machine and the gauge is not spinning. What could be the problem. I have taken the machine apart thinking maybe something is clogging it.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover Deluxe Elite Rewind w lifetime Hepa filter and automatic rewind cord 24ft. but recently it is not vaccuming as sufficent as it did last time used, which is once per week. I do not see where anything is clogged, please advise..

Make sure the hose is installed in the foot when using for the floor. check the belt. when working properly, you should see dirt spin in the dirt cup. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I bought an Electrolux Accelerator vacuum cleaner with a HEPA washable filter last year, and now it won't **** strongly. I think its the hose pipe. I clean the filter every time we use it. I am really frustrated! Any ideas?

Check the suction port it is probably stopped up or take the filter out and crank it up see what happens ... Vacuums

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing

No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

Bin isn't filling, won't pickup and brushes won't spin for the second time. Last time iRobot had to replace both wheel modules. Any suggestions? I clean it every time I use it!

Wheel modules? It's more likely to be the cleaning head module. Clean your brushes exactly as the manual describes-- particularly the yellow bearings. Run the Roomba on a hard floor without the dustbin. Does the brush turn? If not, call support again ... iRobot 560 Roomba Vacuuming Robot, Black and Silver Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it

My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

REPEATDED CLOGGING My unit keeps clogging in the hose right where it meats the brush. My wife and I have cleaned it several times but it continues to clogg after every few uses. What can be done about this?

Are you sure there is nothing else in the dirt inlet. Alot of times a pin or nail will turn sideways and get stuck, then debris builds up and will clog up. It is either that or you are trying to vacuum up too big of things. ... Eureka 2961AVZ Bagless Upright Vacuum

I recently bought an upright MC-E4061 and have a problem with the paper filter clogging prematurely, it needs weekly cleaning. The filter clogs too easily with the main plastic bowl having very little debris! Our older panasonic, used daily, is not problematic. Please could you advise as the paper filter is time consuming to clear.

... Panasonic Vacuums

The spinning brush on the side kept falling off. I would put it back on as the little screw usually remained with the brush. Last time it fell off (it has every time I've used it) I lost the tiny little screw. I cannot find reference in the manual to its specifications. As I have had it for less than a week, I am considering returning it.

Its so annoying to find Roomba after he's finished cleanin only to see that once again he's lost his brush. How to keep your Roomba from losing his brush- items needed: quick steel putty (local hardware store), crazy glue, original screw (or similar ... iRobot Roomba 530 Robotic Vacuum

Kenmore Elite 721.66463500 Microwave died. Didn't even notice until I went to use it. Changed fuse and screen asked to enter the time of day. Entered the time and hit start. The microwave buzzed for 0.5sec and it blew the new fuse I installed.. put in another fuse and the same thing happened.. I measured the resistance in the noise filter. Results: L1-L2 < 1ohm N1-N2 < 1ohm L1 or L2 - N1 or N2 = 0ohms I'm thinking I need a new filter but I also was unable to measure any resistance o

... Vacuums

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha

I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

My dyson will not switch on , the last time I used it the power faded in and out a couple of times I wiggled the lead and it continued to work. However today it will not power up, I have changed the fuse just in case

Hi from uk the symptoms you described is a classic fault with where power wire has broken within the main cable usually at pint where it enters the vac ? hence wriggling wire temporarily makes contact are you sure the wires in plug are ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet

Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Belt squeels when the roller starts turning. only used about 10 times. Small belt under cover is very loose, but it shouldn't be worn out after only about 10 uses. does the small bell just rest on the belt control pin or is it supposed to be around it (thinking it could have slipped off)

Ours did the same thing in about 10-15 uses, the idler pully quits holding the v-belt tight and the the aggitator wont turn. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

It has no suction...last couple of times while using the vacuum it would cut itself off. If I tried to use it the next day it would do the same thing

Hi,\015\012You vacuum is probably plugged up. Flip it over, beater bar up, and remove the plate that surrounds the beater bar. The beater bar needs to come out next. If the belt is good, it will be a little hard to remove. The beater bar si ... Vacuums

I usemy hoover often, and last time I went to use it, it keeps blowing the circuit. It has never done this before, not in any of the plugins used, hoover or electrical problem?

It may be the motor is starting to short ... Hoover F7431-900 SteamVac Vacuum

Vacuum clogged Just had new carpet installed. In trying to vacuum the carpet for the first time, fine particles have clogged the sweeper. I'm using a rainbow sweeper with water reservoir.

If you are talking about the electric hose, try using your none electric hose with the crevice tool attachment to extract the particles from the other one. When using any of the hose please leave it running a few minutes to make sure everything in th ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0558 seconds