Having problems with your Hoover Lynx ?
My Hoover lynx power head does not turn on the brushes.
when I push the on button to turn on the brushes it sometimes works.
Repair Help & Product Troubleshooting for Hoover Lynx
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums
Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.
Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Hoover Steam Vac - Brushes not turned, no suction power
The Brushes not spinning is most likely is caused by seized bearings in the turbine, requiring shop service (easy fix). The suction issue can be caused by the standpipe seal missing or lower recovery tank not on properly, on some models missing front ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The Delta power head is not working. Brush is not turning.
... Electrolux EL6989A Bagged Canister Vacuum
I have a hoover celebrity QS wuith the power head. I have only used the powerhead for years purchased in 75) I removed the powerhead to use the brush and the power does not come on but if I put the powerhead back on it works again.
You have done very well keeping this appliance working since 1975!!!\015\012Lucky you!\015\012I'm not certain you would be able to get replacement parts for this model any longer,\015\012Maybe you will just have to continue with the ... Hoover Vacuums
When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.
This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum
I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of
... Miele S300 Bagged Canister Vacuum
Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.
Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.
... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have an Ambassador canister model Electrolux. The powerhead shut off and the brush doesn't turn. There is nothing wrapped around the brush and the connection from the handle to the power head is fine. Any suggestions? Thanks AG
CHECK TUBE-SUMO ACTIVE ( PART NO: 1131402-02 ) CONNECTION AND NOZZLE-SUMO ACTIVE OR REPLACED (PART NO: 1131400-02) ... Electrolux Lux 7000 Bagged Canister Vacuum
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.
Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
Brush head stops turning once hoovering - Dyson DC35 Handheld Vacuum
... Dyson DC35 Handheld Vacuum
Power head won't work when brushes turned off
The power head motor's only purpose is to operate the brush, so that's normal. ... Hoover S3755 WindTunnel Bagless Canister Vacuum
The red light with an exclamation point is lit and vacuum won't turn on. This happened as I was attempting to change to the brush power head. We've just moved and I can't find the manual. Please advise. Bonnie
... Miele Vacuums
My Hoover U6434 makes a knocking sound when I turn if off and it powers down. The belts and brush roll are fine. Any idea's? Thank you, mpipes
Its probobly a pice of dirt being slung around on some hair or thread. try cleaning the fan and look carfuly for hair tightly raped around the shaft. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Power head is dragging slowing down like the brush is stopping turning and coming back
Have you tried changing he belt ?. Some time the belts stretch out and they don't turn the brushes ... Filter Queen Majestic Canister Vacuum
The green light on the power head was flashing and then it went out and the brush quit turning. Is the a reset button?
No reset button. Most likely your belt broke or it has to be replaced. How to replace the belt look at instructions on our website:http://www.goodvac.com/artic ... Kirby Ultimate G Bagged Upright Vacuum
Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?
I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum
I own a Hoover Steam Vac Plus w/ Rotating Brushes (model#F5871-900), when I turn on the power I hear a medium-loud hum coming from the motor area and nothing works. What could be the issue?
The motor sounds locked up. Water gets in there and rusts the pieces together. The motor could be replaced, but probably not repaired. ... Vacuums
My Hoover Duros (blue color, S3000 something model with the power brush) worked fine for 3 years, than it died. The other day I couldn't turn it on... What can it be? A fuse? Where's is the fist in this model?
Manual > http://hoover.com/file/682/To reset the breaker:(1) Push the ON/OFF switch ... Vacuums
I just accidently vacuumed over a bag, realized what had happened and pulled it out before it got stuck further into the head of my Hoover Wide Path. I shut the machine off, and when I turned it back on the brush won't rotate. Anything I can do?
IS THERE A RESET BUTTON ON THE MACHINE? SOME OF THE MATERIAL FROM THE BAG MAY BE WOUND AROUND A PART OF THE BRUSH. ... Vacuums