Having problems with your Hoover Powermax S3601 Bagged Canister Vacuum ?

How to replace the wire on the main noozle... it is broken from the bend...

\015 Can u tell me how...\015

Answers :

I assume you are talking about the powerhead, on the bottom are some screws, just take out the four with the arrows pointing to them. The others hold the motor and don't need to be taken out. Turn it over and the top cover will come off and you can get to the wire.
\015\012f6f763a.jpg
Repair Help & Product Troubleshooting for Hoover Powermax S3601 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace the wire on the main noozle... it is broken from the bend...


I assume you are talking about the powerhead, on the bottom are some screws, just take out the four with the arrows pointing to them. The others hold the motor and don't need to be taken out. Turn it over and the top cover will come off and you can ... Hoover Powermax S3601 Bagged Canister Vacuum

Wiring diagram I have a replacement main switch for my vacuum cleaner. Two blue and two brown but no diagram or markings on terminals to show which wire goes to which terminal


How to Repair a VacuumCleanerhttp://home.howstuffworks.com/how-to-repair-small-appl ... VAX Appliances 2000 Canister Vacuum

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power Nozzle Model No. N137A (for Electrolux Epic Serial 6500 SR) has a broken wire. Can I get a replacement power nozzle or find a repair place in the Everett, Washington vicinity?


... Electrolux Epic 6500 Vacuum

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!


... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

Oreck Orbiter Hi Could you e-mail me a wiring diagram for the Oreck Orbiter please? I need to replace the mains cable & the cable to the motor. Thank you, Helen Eccott.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618779&thid=681757\015\012Oreck Orbiter\015\012Posted by eccott on Jun 18, 2008\015\012Hi could you e-mail me a w ... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


... Vacuums

My Henry model NV 250 Advice on fitting replacement suppressor which has only two wires. the original suppressor having four wires.


... Henry Numatic "" Canister Vacuum

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.


... Electrolux Twin Clean Bagless Canister Vacuum

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.


Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.


... Vacuums

How to open main case on a dc08. i have removed the two screws under the top filter but i can not figure out how to seperate the main case so i can replace main switch. any help would be much appreciated


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hi I have the Ambassador 337 model. I had to rewire the on off wiring due to the "N" wire rubbing through & breaking. I have it all together again although a piece of wire in the shape of a "V", with a bend each side of it has dropped out & I don't know where it came from!!!! Please send me diagram of this model so that I know where it goes. Cheers Ian.


... Electrolux Vacuums

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?


Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.


The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a


... Hoover S3670 Bagged Canister Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you


Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums

Eureka Boss 4D (5892BVZ) - Switch Replacement & Fried Wires


If you got the handle apart, Id say you can probably fix it yourself. You might be able to patch it but I would say to maximize your effortrs please visit RepairClinic.com to find the exact replacement parts you need. They also have expert advice ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0520 seconds