Having problems with your Hoover S1361 Bagged Canister Vacuum ?
Intermetint starting does not always start when the button is depressed
Repair Help & Product Troubleshooting for Hoover S1361 Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Intermetint starting does not always start when the button is depressed
... Hoover S1361 Bagged Canister Vacuum
Start button does not remain depressed when turned on.
Sounds like a defective switch that won't catch. Is it still under warranty? You could put something higher than, but roughly the same size as the button on it and duct tape it on until you get it replaced. If you're handy you could replace it with a ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you
Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums
Central vacuum won't start even after depressing the reset button on the carpet sweeper. Hose and wand appear to be unclogged.
Is it only the power head that's not working, or the central vacuum itself? Disconnect wands from hose, turn on, and hold hand over hose end to check for suction. If none, go through first set of steps below.\015\012\015\012If the vacuu ... Electrolux Central Vacuum
I have an Amana above range Radarange, Model #AMV4204AAB, Serial # 10168958GE. Tonight after running for a 7 minute period and finishing, it would not again start. There is power to it, but various buttons no longer work. The following buttons won't work: Kitchen timer, Light Timer, #5 button, Popcorn, Poultry, Auto Defrost, and the Start button. Any help?
Hi,\015\012\015\012Push\015\012the power cord all the way into the outlet in case it became loose and\015\012is causing the problem. If the microwave still isn't working, check for\015\012a blown circuit fuse, and repair it ... Vacuums
I would like to always use the GO TO button to go to a specific bible locatilon, but I more often get something else from the square and arrow button.. I would like to always be able to use the GO TO button. How do I do this each time that I wish? [email protected]
Hello\015\012What is it we are working on here?, need specific make and model number of device. You also have this listed under the category of "VACUUM PROBLEMS" is this where you wanted it listed? ... Vacuums
My Dyson DC-17 Absolute Animal does not stay running after I push start button. It will only run if I hold the start button down all the time.
Switches always fail on the dysons. its a pretty simple fix though. let me know if you need parts and/or instructions on repairing it. ... Dyson DC28 Animal Bagless Upright Vacuum
Sharp carousel double grill convection microwave oven R820JS/R820BC - the start button won't work when we try to cook in microwave. Can use timer, start button works, can set clock etc. but cannot seem to cook in oven.
Dear Sirs, I purchased two Braun 5875 Contour Electric Shavers in May 2009. I didn't start using one of these new shavers until August 2010. In January of this year I found that the contour part of my razor started to flex on one side and the spring clip that retained the foil became loose. I didn't get very good shaves from this Braun razor and put it down to the pattern change of the foil itself. I have always used Braun shavers because I was of the opinion that German made articles were alway
I press the start button and sometimes the motor won't continue running. As soon as I release the start button, it turns off. Sometimes, if I remove the cannister and replace it, then it will run correctly. Sometimes not.
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.
How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum
My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Won't start I have a miele, model # s2481 red vacuum. It will not start. When the button is pressed it feels normal, but nothing happens, it will not start. Is this a problem my handy husband can tackle?
It is most likely your cord winder. They are a little tricky to fix yourself. A repair shop will probably charge about $50. To fix it. The contacts where the cord winder plugs into the motor need to be cleaned and adjusted. Just don't let your r ... Vacuums
Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.
... iRobot Roomba 530 Robotic Vacuum
My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.
The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Eureka lightforce 300 poor suction, power paw doesn't spin and self cleaning duster doesn't clean its self when the button is depressed.
When this happens to me I do two things. The first is to empty the cannister but when you do (with the vacuum unplugged) stick your hand up inside of where the cannister goes.Sometimes that is filled with debris. Pull as much as you can out. There is ... Eureka 4718AVZ LightForce 300 Bagless Upright Vacuum
Dyson dc08. I press the start button. It cuts out when i release the button
Faulty switch replace np. Check at local vaccuum repair shops for the switch. ... Vacuums
The extension wand is stuck. It will go up to a certain point and stop. The gray flexible hose that it is housed in is not damaged and there is nothing on the steel metal rod that slips into the hose that I can see. The gray button on the handle still depresses as well and everything is still "Clicking" as far as the button. thank you
I would try the dyson medic .com this is the place that specializes in the dyson vacuum. Good luck ... Dyson DC25 All Floors Bagless Upright Vacuum
Panasonic NN-SD776S microwave Start button stopped working. I know, the first thought is a bad door switch because "everyone knows a microwave should not turn on if the door is open." I am experienced with electronics, but even the timer won't start at all. Funny thing is, I had this exact model do this exact thing just over 2 years ago - troubleshot all the hardware until I was lost, finally bought a new one from Costco (June 4/08). And now 2 years later this one craps out - a 2 year timer
Hello Aaron,Since your microwave is controlled by logic, and the start button / timer portion is not working, I would start troubleshooting the power supply.Get a look at the integrated circuits that are on the circuit board, ... Vacuums
It will not start. I plugged it into many different outlets and it will not start when I press the button.
This could be a faulty on/off switch or a broken lead wire or a faulty motor ... Miele Vacuums
When I plugged in my Riccar Vacuum cleaner - it made a pop sound. The breaker had not been moved - there was no smoke or apparent damage. I tried to depress the restart button and nothing happens. Is there a technique about pushing the restart button. Please advise.
Check the cord where it goes into the machine on back. most likely blew out at machine ... Riccar 8955 Upright Vacuum
The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill
Is the front bumper **** in? ... Roomba Vacuums
I pushed the on button and kirby g5 starts but when releasing button motor stops
Hello,\015\012You can replace your own Kirby switch with my guide. Here's the link...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
I have a two yr old Ariens model 939003 (5 HP 4-cycle) and it will not start! Have rel new gas, and an electric starter. Think I did everything right. Ignition key on and choke full; primed push button x 3 (at first when I was trying to mechanically start it I over primed it). Spark plug clean and dry. What next?