Having problems with your Hoover S1361 Bagged Canister Vacuum ?

Hoover dimension 1000

\015 The power switch on my hoover dimension 1000 CANISTER vacuum cleaner stopped working. The switch is located on the top of the canister not the handle, How do I get the top off so that I can get to the inside and take a look at it?\015

Answers :

There are a few screws on the bottom of your hoover, remove them using a suitable unarmed and then pulling firmly upward.
Repair Help & Product Troubleshooting for Hoover S1361 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On a Hoover Dimension, frozen impeller

... Hoover Vacuums

Hoover dimension 1000

There are a few screws on the bottom of your hoover, remove them using a suitable unarmed and then pulling firmly upward. ... Hoover S1361 Bagged Canister Vacuum

Hoover Dimension has no suction and it smells of something burning

Pets in house? check all hose passages for "hairball" clog...and check the drivebelt that spins the brush...(some have an electric motor to spin the brush, thus no belt) ... Hoover Bag Paper Microfilter Dimension Upright 3 Pack

New Hoover Dimension Supreme vacum belt can't be installed. No

... Hoover U5227-930 Elite Upright Vacuum

No suction on my Hoover Dimension

If you smell something burning unplug until problem is found and fixed, suspect if no suction hose is blocked and if brush wheel it or the belt may be causing the smell, a bad or failing motor is less likely but possible. ... Vacuums

Hoover Dimension 1000 quadraflex - Vacuums

... Vacuums

How to change power cord of hoover dimension 1000

... Hoover Vacuums

How do I install the belt in a Hoover dimension II vaccuum?

Take off the bottom plate, then you can get to the brush roll and the belt. The belt goes around the brush roll and goes to the motor shaft. If you can't see the motor shaft, then you will have to take the top cover off to get to it. ... Hoover Vacuums

Change vacuum belt on hoover dimension U5209

... Vacuums

I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums

Same problem my vacuum cleaner is Hoover Dimension 1000

Witch model due you have ? ... Vacuums

Hello I need a set of rear wheels to my TurboMaster Hoover. If you provide me an Email address, I can send you the drawing + picture. Is it possible to purchase it from you. (I'm living in Israel) Best Regards Zeev Priester 24 Beit Ha'Shita st' PO Box 698 Bat-Hefer 42842 Israel Mobile: +972-(0)52-4299716 Email: [email protected] [email protected] SKYPE: zeev.priester

... Hoover Vacuums

Belt Replacement How do you change/replace the belt on a Hoover Dimension Supreme vacuum?

Take the bottom plate off, the brush roll and belt are there. the belt goes around the brush roll and hooks to the motor shaft. If you can't get to the motor shaft, then you will nee to remove the top cover also. ... Vacuums

HOOVER Dimension Vacuum Model U5209-930 Manual

... Vacuums

How to open and change bag on Hoover dimension 1000

... Dimensions Vacuums

Hoover Dimension Vacuum - No suction - Any suggestions?

Your fan broke. This is a direct air motor, which means what you pick up goes directly through the fan and they break if you pick up something too big. It's an older design and fortunately one that is made to be repaired. The Fan Part # is 38755030. ... Hoover U5227-930 Elite Upright Vacuum

I have a Hoover cannister vacumn cleaner Dimension 1000 Serial number 0040229 and model number S3283 How do I open it to put in a new bag?

... Vacuums

How do I get at the cord rewinder for a hoover dimension 1000

... Hoover S3639 WindTunnel Bagged Canister Vacuum

Hoover dimension 1000 dead after hot - Vacuums

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=557355\015\012Generic problem for all Vacuums\015\012Hoover Dimension 1000 dead after\015\012Posted ... Vacuums

Hoover Model S3281, disassembly instructions


I recently bought a samsung silencio hoover and it has just stopped working whilst i was in the middle of hoovering, when i took the panel off to empty the contents the filter was really hot, has my hoover blown up? I was only had the hoover 4 months?

... Samsung Vacuums

My Miele vacuum cleaner has the red triangle light on and keeps switching on and off. Is it broken? have been hoovering upstairs and I noticed the hoover had the red triangle light on. I changed the hoover bag but it still kept going on and off. Is this an overheating problem or is the hoover on the way out?

... Miele Vacuums

Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!

Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums

Hetty hoover not working. It was working ok until I opened it up to search the bag for a missing jigsaw piece and I put it all back and I hoovered the mess on the floor, then switched off and switched on and hoover would not work? Is there a cut off button on Hetty hoovers?

Know cut off switch, its just not getting power ? 2 things its ether at the wall plug or in side the unit. I have never found a fuse in side them , so it may be just a lose wire did you try other plugs in the house . good luck DFD ... Henry Numatic "" Canister Vacuum

I was using my Henry Hoover as usual. When i sucked up quite a fair sized puddle of water. The hoover instantly cut out and a strange burning smell was coming from it. Would this be the fuse, motor etc ? Or would it be worth my while just replacing the entire hoover ?

Hi. I have to wonder why anyone would **** up a puddle of water with a dry vacuum cleaner (with no earth lead). I realise that your question may simply be a joke, but if you are serious, I think it is probably fair to assume that it is now dead and p ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2800 seconds