Having problems with your Hoover S2220 Flair Bagless Upright Vacuum ?

Motor housing is hot

\015 The housing is hot and has emits an odor when running\015

Answers :

This model has 2 side filters, check and clean those. Be aware that this is a quick clean vac, not to be used for extended periods of time to replace a full size upright. clean the inside filter in the dirt cup.
Repair Help & Product Troubleshooting for Hoover S2220 Flair Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?


Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

Motor housing is hot


This model has 2 side filters, check and clean those. Be aware that this is a quick clean vac, not to be used for extended periods of time to replace a full size upright. clean the inside filter in the dirt cup. ... Hoover S2220 Flair Bagless Upright Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?


I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

MOTOR LOUD HOW DO I DISASSEMBLE MOTOR HOUSING TO LOOK AT MOTOR. TOOK OUT SCREWS ON BOTTOM BUT CANNOT GET TO MOTOR.


... Hoover V1 SteamVac SpinScrub Vacuum

Motor problem When i plug my steam vac in the motor sparks and smokes. It smells as if the motor is burning out. I've tried different outlets through out the house and get the same outcome, what can i do to solve this?


Nothing you can do im affraid its the motor armature so unless it can be stripped down then you will need to replace the motor i would get a price for the motor to decide if it is worth doin sorry. ... Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Nutone model cv-350 vacuum motor will not shut off. I have to unplug system in garage. I disconnected wire to house vacuum inlets and motor is still running. There must be a reset on the motor. I have turned the external switch on and off and still no help.


Mine is the same, and it is the relay welding itself closed. The relay is switched by the low-voltage wiring that connects to the vacuum outlets, and it switches the motor on and off. Mine was welded in the energized position. I have cleaned and file ... Vacuums

Dyson DC07 Vacume cleaner trips on thermal after 10 min motor not excesive hot resets after 15 min has been doing this for the last 3 mths. Could it be faulty thermal or motor overheat how can I check without changing motor


First, check both filters on that unit. the premotor filter on the side, and the hepa filter underneath the canister. if those filters are clean move through the suction channel and look for a clog or obstruction. also make sure the canister is clean ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

How to open the motor housing.


Pls i want put music in my phone but its not possible i need ur help ... VAX Appliances 2000 Canister Vacuum

Kirby Heritage II Replacing the Motor in the housing HELP!


... Kirby Heritage II Vacuum

H3000 Motor becomes very hot during use


Over heating on a floormate is cuased by obstructions or a clogged up filter. Try running it without the recovery tank. If it doesn't over heat you need to check for obstructions in the nozzle and the tube leading up to the recovery tank. if that ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Hoover EmPower 4600 keeps blowing circuit breaker. The number of outlets in the house that will allow me to run the vacuum is dropping quickly. It is a 4 year old house and all the circuit breakers are 20 amps. The vacuum only has a 12 amp motor. I am at a loss to solve this problem.


Take it to a friends house and plug it in if it does the same thing then the problem is in the vacuum cleaner.check your cord and see if there are anny cuts in it.you can open the breaker box then plug in the vacuum and watch the breaker box.you migh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The motor on my Dyson Animal DC07 is getting very hot. I've always kept the filters and such clean. Is there any maintenance I am to be doing with the motor?


Hi its Darran at Dyson.From your description of the problem, it sounds as though there is a lack of airflow to the motor which is caused by a blockage in the machine or a dirty filter. To check your machine for a blockage, ple ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?


Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0547 seconds