Having problems with your Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum ?

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please?


Answers :

A bit late for the original questioner, but perhaps this will help someone else.\015\012
\015\012There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about the others.\015\012
\015\012Anyway, this is it. The cover is held to the base by 8 screws. Two are clearly visible near the handle, two are in the bag compartment. They are easy!  The problem is finding the others, because they are concealed by the foot-operated switch plates, and you have to get those plates off without breaking them.  \015\012
\015\012Basically, those plates slide off backwards (i.e. away from the handle end) but you have to release a plastic catch first.  The catch is part of the switch-plate, and is located roughly mid-way along the straight side of the plate, just by the raised bump.  You can just see the catch if you shine a torch light down the gap.  The catch is released by inserting a small screwdriver or other flat blade and levering it away from the centre-line of the machine.  If you apply gentle rearward pressure on the plate while doing this, you will soon feel when it's released.\015\012
\015\012Once the catch is released, the plate will slide off completely and the remaining four screws are revealed.  After that, it's simple!\015\012
\015\012Hope this helps someone!
Thanks odin223. I had tried for hours to get the cover off my telios 1500. With the above info I had it solved in 10 mins! Wish I checked the plug first though! The reason the Hoover wouldn't trun on was a broken wire in the moulded plug.
Repair Help & Product Troubleshooting for Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?


Which model do you have.. ... Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please?


A bit late for the original questioner, but perhaps this will help someone else.\015\012\015\012There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

Hi , I have replaced the electric cord on Electrolux Lux Royal vacuum , but the rewind that retracts the cord does not pull it in . The coil spring looks ok but it will not pull the cord back in , any suggestions please . Thanks Dave Ryder


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564353\015\012Generic problem for all Vacuums\015\012Hi, I have replaced\015\012Posted by dryder on May 02, 2008 ... Vacuums

How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>


What model is this for? ... Kenmore Vacuums

I have an earlier model Weed Eater blower/vac 1925. the starter cord pulled completely out of the hub. I have taken the housing cover off and examined the starter. for the most part everything looks fine but I am unaware of how the starter cord should be recoiled around the starter. any suggestions?


... Vacuums

Bissell 1699 I have taken apart the pro heat cleaner. I reassemble it. The top cover will not go all the way down. Any suggestions on getting back together. Thank you


Make sure that the piston on the bottom of the smart mix valve is in the water only position.(needs be be on the knob and not sitting in the hole). With the top off, it is easier if you have a block of wood or something under the base to hold it up. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have model # EC2T-36 HPF and TCP# 12536Q and I am looking for a repplacement ballast and a light cover but I am having trouble finding the parts department online and the 1-800 number on the fan is a musuem line. So I need help to get these few parts. can you help please? Matt 937-572-2386 Thank you, Matt


... Vacuums

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.


... Miele S558 Red Velvet Bagged Canister Vacuum

How do you get cover off dyson dco7 to replace electrical cord?...I can get the torx screw out, but the cover seems awfully tight and I don't want to break the cover


I would use a toilet plunger. ... Vacuums

Replaced plug on retractable cord...but forgot about size difference, cord retracted inside and can't get it out...is there a way to get at it?


You have to split casing . Small screws underside could be hidden by feet ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet


Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!


Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?


... Windsor SR12 Sensor Bagged Upright Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

A piece of string / cord has wrapped around my Kenmore spinning brush end on the 12 Amp Power - Mate. How is the best way to get the cord off?


Cut the string with a knife or scissors and pull it off. You can turn the brush manually to ensure you get it all. ... Kenmore 22313 Bagged Canister Vacuum

I have a progressive 360 model 116.27814. I want to change the exhaust filter and I cannot get the filter cover off of the back of the canister. Please give detailed instructions. I am afraid that I will break the cover, because I can't see how it should detach.


There should be tabs that need to be pressed in, and will allow the filter cover to be removed to access the filter. On some models, the tabs are accessed from the bottom by tilting the unit on its side, or by simply pressing them in from the top, th ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of


Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!


Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum

I lent it out (NEVER AGAIN!) got it back and no water squirts out of it in front I looked at it with the cover off but it doesn't come all the way off anyhow nothing looks clogged the belt is all fine too. Clean all the grime is seen and still doesnt work. What's wrong?


It might be pet hair caught in its hose. You might have to disassemble everything just to be sure. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

On/off switch not working. How do I get the plastic cover off to look at it? I think it's probably a very simple fix if I could get to it. Have to unplug it to turn it off.


Hello, my Dyson is dead, i've replaced the on/off switch with no change. To get at the switch, firstly pull off the bag/syphon box and then remove the handle. Behind the handle you will find 2 torx screws and 3 clips, when you have removed the screws ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0984 seconds