Having problems with your Hoover S3577 Vacuum ?

How do you remove the strain relief bushing #163768 to repair the cord?


Answers :

Repair Help & Product Troubleshooting for Hoover S3577 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you remove the strain relief bushing #163768 to repair the cord?


... Hoover S3577 Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Repair cord on simpilicity 7850 vacuum cleaner


... Simplicity 7850 Premier Bagged Canister Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.


When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

How do i open canister for cord retract repair


There are four screws under the lid, and there are two additional screws under the face plate for the controls display. You'll need a thin, flat blade screw driver to "pop" the face plate off. The two additional screws that you are looking for are ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Miele white star vacum cleaner - electrical cord not making contact when plugged in - sometimes 'jiggling' cord at base, it will make contact and work...pls help..where can i get it repaired in nyc, or can i repair it myself


... Miele Vacuums

Panasonic vacuum cleaner model mc 6640- unable to remove cord lock


... Vacuums

I was blowing snow with my Toro Power Curve 1800. I was distracted for a moment and tangled the cord in the blade. The cord is wraped around tight, how can I remove the cord?


Unless you are able to turn the blade backward and pull on the cord at the same time no luck. it may be easier to just cut the cord and install a new one. solution one is best and both require taking the machine apart. start there and hope it works o ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.


If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?


Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums

I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?


The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

Problem with cord rewinding mechanism on my Nilfisk King!Whilst repairing broken cord(successfully)the metal coil thats part of that mechanism sprang out!Can someone out there tell me how to put it back together again PLEASE.I would so like my cord to be able to retract again


... Vacuums

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

Model 116-22812203 How do I open the canister to repair a cord


... Kenmore 25512/ 25513 Progressive Canister Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I am a Philips pensioner and purchased a "AZUR EXCEL PLUS 555" steam iron from them many years ago.There is now a fraying of the cable as it leaves the iron with resulting in arcing. There is a detachable backplate on this model which allows corded or cordless use but which cannot be accessed to allow for cable repair by the user. My qustion is can this be repaired or if not can I still purchase a replacement backplate complete with new cable as I this is a great iron and a credit to philips


... Vacuums

My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this may be the cause yet it ran fine last time it was used! so I am at a loss, please help if possible.08/31/2010 Steve


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jigglin ... Windsor SR12 Sensor Bagged Upright Vacuum

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?


Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

I have a Euro Pro Compact Performer model # EP 171 which I love. It is the best iron I have found for my quilting class. When I went to use it, I found my cats had chewed the cord to the point that it is unsafe. I took it to a repair shop to have a new cord put on it and they told me it had to go back to the factory. I do not want to purchase another iron because it is my understanding this model is no longer made and because I love it. May I send this iron back to the factory to have a new


Hi, you may already have found a solution, but I recently saw this same model iron on ebay! ... Euro-Pro Vacuums

How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>


What model is this for? ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0705 seconds