Having problems with your Hoover S3639 WindTunnel Bagged Canister Vacuum ?

The main motor quits after just a bit - now is making a thumping noise

\015 I wondered if it might be overheating. Cleaned the filters, but problem did not go away. Is not suctioning well.\015

Answers :

Repair Help & Product Troubleshooting for Hoover S3639 WindTunnel Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The main motor quits after just a bit - now is making a thumping noise


... Hoover S3639 WindTunnel Bagged Canister Vacuum

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started


There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Central vac motor quit, blew fuse, when fuse reset motor makes a whirling noise and shuts off


... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Vax powa 4000 wet and dry - no suction Both power and pump switches light up. Pump makes clicking noise. Vac motor only powers up briefley when in switched on cindition and mains plug is being inserted into socket.


... Vacuums

Motor on mod 8975 making inordinate amount of noise disassembled 1 intake source at a time - still making noise can't figure out access to motor


The complete repair details and manuals for you bissel device is available on this link .\015\012\015\012 ... Bissell Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hi folks, my beam vacuum makes a very loud roaring noise quite often. the problem started when i was vacuuming up a quantity of vermiculite from my chimney. i think i overloaded the vacuum i think and it made this loud roaring noise. the vacuum tends to make thos noise when i am hoovering after 5 minutes or so. any ideas?. thanks in advance Tom....


If the filter bag is bad and didn't trap all of the dust, then it got into your motor, so you may have a problem with your motor now. ... Vacuums

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise


This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

Motor makes rattling noise when Vacuum slows down.It stll has normal suction.Also at high speed it makes awhinning noise that you can stop by squeesing the the cannister.


There might be something trapped inside the foot of the machine.Remove the cover and look for something that is too large to go down the pipe. ... Vacuums

Beater bar motor quit, now the main motor quit. Replaced the on/off switch. still nothing


See this causes and fix it. God bless youIf the vacuum cleaner motor doesn't run the on - off switch might be \012turned off or defective. Test the switch with an Ohm meter or continuity\012 checker. \012 If the vacuum ... Vacuums

Bosch terrossa 1700w vacume cleaner make load noise when turn up tp high setting and the motor make a shorting out noise


... Bosch Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a model 6100 healthy home vacum. When it's turn on the motor make a very loud noise. I took it apart and blew some dust out of it. And it still make the noise.


Hi,\015\012Usually when a vacuum is making the loud noise it is because of a stoppage somewhere in the vacuum.\015\012To find the blockage some detective work will be needed.\015\012First off take off the hose at the closest point t ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

Hi. My dyson dc14 wand works great then all of a sudden if something too big or even just the carpet it makes a sucking noise & the purple round bit in the actual Hoover makes a funny noise & then the suction isn't as great. If it turn it off then on again it comes back to normal! Help!!


Sounds like a blockage. I have a DC14 and I have never had this problem. You can easily remove the wand from the flexible hose and the flexible hose from the machine to check for a blockage. Don't allow paper or larger items to go into the machine, e ... Vacuums

Vacuum making high pitched noise and smells like motor is burning


Try repair first for quote and if too expensive then replace. 5 years is about the average life span. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Making high pitched squealing noise and motor is hot...cleaned out brush area and made sure hoses were free and clear too..noise is coming from the brushes because when I use just the wand, the noise disappears


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

HI , I REPLACED MOTOR BRUSHES ,BUT MOTOR IS MAKING A FUNNY NOISE ,AS IF MOTOR IS LOOSING CONTACT ,LIKE A BURNING SMELL. CHEERS


Hi there, \012Most likely you have a damaged commutator. I used to change the brushes on the dyson vacuums but what i found is that it is almost never completely successful. THe Dyson motor is not as good quality as say a miele and when the bru ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0454 seconds