Having problems with your Hoover S3639 WindTunnel Bagged Canister Vacuum ?

Rollers are to low and tearing up carpet.

\015 How do you adjust the rollers height so it does not tear up carpet? Vac. as well as the carpet are new.\015\012Thanks\015\012DB\015

Answers :

Unfortunatly you cant adjust the height on that type of machine, and new carpet no matter how good or expensive can shed for up to a year, the best thing would be to buy a cheap carpet rake ( not a garden rake ) that would get up all that fluff.
Repair Help & Product Troubleshooting for Hoover S3639 WindTunnel Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rollers are to low and tearing up carpet.


Unfortunatly you cant adjust the height on that type of machine, and new carpet no matter how good or expensive can shed for up to a year, the best thing would be to buy a cheap carpet rake ( not a garden rake ) that would get up all that fluff. ... Hoover S3639 WindTunnel Bagged Canister Vacuum

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.


Hi Peter, I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc17 sits low on my carpet in carpet mode and the brush does not roll. If I lift it off the carpet it rolls just fine. What can I do? It sucked in a shoe string. And a little after it starte


Probably the teeth on the belt av stripped and needs new belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?


Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

The hoover shampooer will not extract the water from carpet, is it because the carpet is so low ?? the carpet is cleaning fine there is VERY poor underlay and then wood under that, worried about the wood getting wet and not drying out HELP


Do you have suction at the front of the base,if you don't then look at the plastic cover on the base,you should be able to see through the plastic.the suction slot on the bottom front of the base is very narrow.i don't know if you have pets but most ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller Bar is abrading (removing the fabric of) our carpet. Is there a softer brush or another solution? Has anyone else observed this problem?


Hi Mark,If you're concerned about the suitability of your DC25 for this particular carpet, I'd encourage you to email us at [email protected], as we'd appreciate the opportunity to provide further assistance.We'll look forward to h ... Dyson DC25 Animal Bagless Upright Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?


Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Roomba Discovery will not do our carpet. It is a medium pile tan carpet so it should be OK but it runs for a little while then shuts down and beeps. It does not try to restart.It works well on floors. I have recently done a full tear down and cleaned the drives and brush transmission.


... Roomba Vacuums

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet


Saw another answer saying to put electrical tape on the brush roller where the belt contacts it. I was thinking that the brush roller bearings have probably worn out, and the roller needs to be replaced. But electrical tape is a lot cheaper. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Vacuum height won't go on low carpet setting. Dial will go on medium and high, but not low.


Make sure you're not trying to adjust w/ handle in upright locked position because thewre is a cam which raises the vacuum head a little bit when handle is locked in upright position. If this is not the problem, turn vacuum upside down with handle in ... Hoover Vacuums

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?


You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Vacuum won't pick up any dirt - there's no roller marks when vacuuming carpet. Roller does turn and filters are clean.


Hi,\015\012\015\012When you turn the roller, you should feel some resistance from the belt. Remove the base blate that surrounds the beater bar. Check the belt. Take care in removing the beater bar, so you can get it back in the same w ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Brushes do not spin when it is on low carpet you have to have the knob on high carpet for it to work.


That means that the belt is starting to wear. When the belt starts to stretch it can't turn the roller brush against the resistance of the carpet. The lower the setting the more resistance. You simply need to change the belt. Here is a link to the be ... Eureka 2961AVZ Bagless Upright Vacuum

Dyson DC04 hello, my dyson seems to run ok in upright but when i tilt back the motor sounds like it is struggling, do you think it's down to the rollers being to low and can you adjust height of rollers to overcome said problem? yours chris


Hi.\015\012\015\012If the motor is struggling check to see how easy it is to rotate brush by hand it is stiff to rotate the bearings in the roller may be siezed or the roller could be clogged with hair etc check it & let me know what ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Edge of carpet went into carpet; was removed, but now all rollers on the unerside don't function.


You didn;'t say what the problem is, but I assume that the brush roll is not turning. Take of the cover over the brush roll, then you can get to the brush roll and the belt. The belt probably came off or broke. Best to replace the belt. ... Vacuums

Levels/Settings I am having trouble changing the setting on my vacuum from 1 or "Low, Hard Surface" to any other setting. Without changing it, I am unable to vacuum on my carpet, since the setting is too low.


These height adjustments are designed so that they will not adjust when the handle is in the "back" position. This is so they will stay where they are set and not self-adjust while you are vacuuming. To change the setting, you need to return the hand ... Hoover Elite Rewind Bagless Upright VacuumVacuum

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?


The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0356 seconds