Having problems with your Hoover S3755 WindTunnel Bagless Canister Vacuum ?

Power head with brush not working

\015 Power head only works if held at certain angle. -- interesting that the same problem should manifest ... I have a same issue. I replaced the middle cord, that worked briefly but I have the same problem again. The plastic tab that connects the hand unit to the brush unit broke so not a good contact. Looks like I will have to replace the entire hand unit with the hose -- looks like one piece. Would anyone know the part number and where one might order it on-line?\015

Answers :

Repair Help & Product Troubleshooting for Hoover S3755 WindTunnel Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of


... Miele S300 Bagged Canister Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run


If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

The Delta power head is not working. Brush is not turning.


... Electrolux EL6989A Bagged Canister Vacuum

Power head with brush not working


... Hoover S3755 WindTunnel Bagless Canister Vacuum

I have a hoover celebrity QS wuith the power head. I have only used the powerhead for years purchased in 75) I removed the powerhead to use the brush and the power does not come on but if I put the powerhead back on it works again.


You have done very well keeping this appliance working since 1975!!!\015\012Lucky you!\015\012I'm not certain you would be able to get replacement parts for this model any longer,\015\012Maybe you will just have to continue with the ... Hoover Vacuums

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Power head brush and light work fine but the cannister motor(suction) does not come on.


Hi,\015\012 Quite often there are electrical plugs that connect the two parts of the vacuum, that can get dirty and or corroded. If yours has the plug type connections, please check and clean them. Also, try with the unit on, push on th ... Vacuums

Power head won't work when brushes turned off


The power head motor's only purpose is to operate the brush, so that's normal. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

I need to know how to disassemble the power head for my pet vac. the brush no longer rotates, and it severely limits the quality of vaccuming. we have dogs, so it's really important for this thing to work at it's best!


... Euro-Pro Shark 18Volt Pet Perfect II Cordless Handheld Vacuum Cleaner

Electrolux ultra silencer power head not working


... Electrolux Vacuums

Beam solaire hose only works to suction The power head isn't working. Have another hose and the power head does work on that one so I know it is the hose


... Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Where would I find a replacement power head with brushes


Try this link belowhttp://www.vacpartswarehouse.com/FANTOM-vacuums-bags-belts-brushes-parts-and-accessories-s/4206.htm ... Fantom Vacums Lighting Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

The power head on my kenmore 22822 Canister Vacuum won't work? the power upholstery head works fine.


I have the kenmore whisper belt and i have a reset button on mine ... Kenmore 22822 Canister Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Central vacuum power head no work


Looks like a Beam central vacuum www.beamvac.com, and a Kenmore vacuum head.Reply what problems you are experiencing and I will try to help. ... Vacuums

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?


Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

GE canister vac 106766 power not going to brush head


I've had this same problem. It's a design defect in the power cable running through the hose. The entire hose will have to be replaced at a vacuum repair shop. The part is about $100. I've replaced it once, got an extra year out of it, and am rea ... GE 106766 Bagged Canister Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0912 seconds