Having problems with your Hoover S3755 WindTunnel Bagless Canister Vacuum ?

Hoover s3755 bagless windtunnel canister

\015 Power head will not run.\015

Answers :

Very likely it's the cord at the nozzle neck. These cords flex when you vacuum and they often break internally where the cord goes into the neck. Turn the vacuum on and wiggle the cord at the powerhead and see if the powerhead comes on and off. If this happens, then you will have to replace the cord.
\015\012On some of the early models, the receptacle in the hose, where it plugs into the top of the wands, will break away from the plastic pins it sits in, and the receptacle will slide back into the handle, which means that it will not plug into the powerhead connection when you connect the hose. You can check this by looking at the end of the hose and observing if the receptacle is sitting flush with the opening it sits in. If it is pushed back, it will not make a complete connection with the powerhead cord that is sitting at the top of the wands.
I noticed the brush spins slower when the vacuum motor is running. Checked the voltage goign to the powerhead and sure enough over 3-4 seconds it drops by several volts when the vacuum motor is powered on. I noticed the wiring in this machien is very flimsy. I will be trying to run a separate wire along the hose to power the powerhead and see if that.
Repair Help & Product Troubleshooting for Hoover S3755 WindTunnel Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover windtunnel bagless canister fuse - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover powerhead not working - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Suction will not turn on - Hoover S3755 WindTunnel Bagless Canister Vacuum


Might be the switch is faulty or the vacuum motor is not being activated or the motor by itself is defective.\012You might have eto take a look through the wiring to confirm if the volatge flows from the switch to the motor. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover S3755 WindTunnel Bagless Canister Vacuum brush not spinning


The belt might be streched or broken,also you could have dirt in the bearings on each end of the brush bar. either one of those will cause it not to turn. You will have to remove the brush bar to check that is does not have debris in it. you cant tel ... Vacuums

Brush does not rotate belt is good no jam - Maytag Hoover WindTunnel S3755 Vacuum (Canister Bagless HEPA)


... Maytag Hoover WindTunnel S3755 Vacuum (Canister Bagless HEPA)

Powerhead works but suction - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover s3755 bagless windtunnel canister


Very likely it's the cord at the nozzle neck. These cords flex when you vacuum and they often break internally where the cord goes into the neck. Turn the vacuum on and wiggle the cord at the powerhead and see if the powerhead comes on and off. If th ... Hoover S3755 WindTunnel Bagless Canister Vacuum

No longer pick ups - Hoover S3765-040 WindTunnel Bagless Canister Vacuum


You need to replace the belt. It won't pick up if the belt is worn or stretched. Here is the belt you need:Hoover S3765040 Belt ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Where can I find an extension hose and wand for a hoover wind tunnel bagless canister model S3755 (59134002)


WHERE CAN I FIND AN EXTENSION WAND FOR MY EURO-PRO ULTRA STEAM SHARK II  EP908? ... Vacuums

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?


The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

No suction on hoover s3765-040 windtunnel bagless canister vacuum


It might need a new belt this link is for manualhttp://hoover.com/file/402/ ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover windtunnel bagless canister not turning on at all. we mistakenly dropped it after the first time it happened and it started working again. after using it the next time, it has stopped working once again. help!


... Hoover S3755 WindTunnel Bagless Canister Vacuum

No power My Hoover S3765-040 WindTunnel Bagless Canister Vacuum does not seem to receive electricity to power the vacum. One day it worked and the next it did not. Any recommendations for a solution.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

S3755 Hoover canister bagless vac no power to head


... Hoover Vacuums

Hoover Windtunnel model 6626 900 no suction - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel hose clogged - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Dust collects on outside of canister on Hoover twin chamber bagless cleaner . I have replaced the filter & rubber gasket at bottom of the canister ,checked for blockage.


... Hoover Vacuums

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Hoover Windtunnel Bagless bolt fell off


With this self propell series, the entire bottom needs to come apart to re-install the nut. if it is one month old I would highly recommend taking it in for warranty service. What plastic is melted? ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover WindTunnel Canister: Roller brush motor not turning


These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Solutions for hoover sh40060 - Hoover SH40060 Bagless Canister Vacuum


... Hoover SH40060 Bagless Canister Vacuum

Hoover u6634-900 power cord replacement - Hoover U6634-900 WindTunnel Bagless Upright Vacuum


... Hoover U6634-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel wheel spring location - Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum


Hello irishud. Go to searspartsdirect.com\015\012\015\012Enter your model number and you will get the schematics that show you exactly the wheel spring location. Joe\015\012\015\012Thanks for choosing Fixya! ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum

Belt replacement for Hoover U5100-9RM - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Replace main body on Hoover U8144-900 - Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum


... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0907 seconds