Having problems with your Hoover S3755 WindTunnel Bagless Canister Vacuum ?

Suction will not turn on - Hoover S3755 WindTunnel Bagless Canister Vacuum


Answers :

Might be the switch is faulty or the vacuum motor is not being activated or the motor by itself is defective.
\012You might have eto take a look through the wiring to confirm if the volatge flows from the switch to the motor.
Repair Help & Product Troubleshooting for Hoover S3755 WindTunnel Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suction will not turn on - Hoover S3755 WindTunnel Bagless Canister Vacuum


Might be the switch is faulty or the vacuum motor is not being activated or the motor by itself is defective.\012You might have eto take a look through the wiring to confirm if the volatge flows from the switch to the motor. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Powerhead works but suction - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover windtunnel bagless canister fuse - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover powerhead not working - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

No suction on hoover s3765-040 windtunnel bagless canister vacuum


It might need a new belt this link is for manualhttp://hoover.com/file/402/ ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover canister vacuum (windtunnel)- turned it on and it had good suction, then smoke came out and it smells like something is burning. Is it the motor burning up or something else?


Probably the belt..\015\012Turn it over so the bottom is facing up..\015\012Remove the plate that surounds the brush..\015\012Check to se if brush is spinning frely and that the belt is on there poroper ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush does not rotate belt is good no jam - Maytag Hoover WindTunnel S3755 Vacuum (Canister Bagless HEPA)


... Maytag Hoover WindTunnel S3755 Vacuum (Canister Bagless HEPA)

Hoover S3755 WindTunnel Bagless Canister Vacuum brush not spinning


The belt might be streched or broken,also you could have dirt in the bearings on each end of the brush bar. either one of those will cause it not to turn. You will have to remove the brush bar to check that is does not have debris in it. you cant tel ... Vacuums

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Windtunnel model 6626 900 no suction - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Wind tunnel t series vacuum won't turn on - Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107


I had the same problem and used a tool to clean out the suction tube on my Windtunnel Series T. It was full of junk packed in tight. After cleaning it out there's no more turning off or overheating. It actually works better than when I first got it ( ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

I have a Hoover Mach 3 Cyclonic bagless upright vacuum. It works for a room or two and then it just shuts off. Then it won't turn back on for hours. Any suggestions on how to make it stop doing this? The canister is cleaned out.


This vacuum is very picky about air flow clean the filters and that should do it ... Vacuums

No longer pick ups - Hoover S3765-040 WindTunnel Bagless Canister Vacuum


You need to replace the belt. It won't pick up if the belt is worn or stretched. Here is the belt you need:Hoover S3765040 Belt ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belt works fine but there is no suction - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


This usually indicates a clog in the hose and airflow system. It's most likely to be behind the filter in the tank or in the power head area.\015\012Detach hose from power head and look inside. If you can't see anything, try dropping a penny ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

No suction with Hoover Elite cyclonic bagless canister vacuum


Check your air way to make sure it is not plugged and then if ok you may have to change the filter ... Vacuums

Hoover windtunnel bagless canister not turning on at all. we mistakenly dropped it after the first time it happened and it started working again. after using it the next time, it has stopped working once again. help!


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

REPLACING SUCTION HOSE - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover windtunnel bagless vac that is several years old. the floor vacuum part still works fine, but the handtool attachment has no suction and is useless all of a sudden.


Don't have your model number, but some have a valve down on the noozle part that may be broke. When it is its upright position, the valve won't change over to the hose only position. You would have to remove the top cover to see this. ... Vacuums

No power My Hoover S3765-040 WindTunnel Bagless Canister Vacuum does not seem to receive electricity to power the vacum. One day it worked and the next it did not. Any recommendations for a solution.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Hoover s3755 bagless windtunnel canister


Very likely it's the cord at the nozzle neck. These cords flex when you vacuum and they often break internally where the cord goes into the neck. Turn the vacuum on and wiggle the cord at the powerhead and see if the powerhead comes on and off. If th ... Hoover S3755 WindTunnel Bagless Canister Vacuum

My hoover U5720950 windtunnel bagless vacuum loses suction when I lower the handle.


When you lower the handel it is pinching the vaccume line constricting suction ... Vacuums

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?


The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

Roller brush does not turn - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


The drive belt is worn. you can get the replacement belt here:http://vacbelts.com/hoover-windtunnel-38528-035-belt.htm ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1224 seconds