Having problems with your Hoover S3765-040 WindTunnel Bagless Canister Vacuum ?

Belt will not stay on hoover windtunnel s3765

Answers :

The Hoover Windtunnel™ Self-Propelled models have two belts, a flat belt and the V-Belt. This V-Belt is the one that drives the Brush Roller. \015\012After about three months, most belts stretch out causing them to slip. This means the brushroll turns slower or not at all and the self-propelled becomes increasingly harder to push. \015\012It is recommended that both belts should be changed at the same time.
Repair Help & Product Troubleshooting for Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Windtunnel Hello! I had to change the flat belt on my vaccum and now the belt won't stay on. I can replace it, use the vaccum, then the next time the belt comes off. Is there something I did not do right? Thanks for your help! Jennfer

Your belt may be twisted inside-out. Be sure the printed marks on the belt face away from the pulleys and shaft. The printing should face you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt on my hoover will not stay on. It falls

Okay. I would suggest that you have a problem with your roller brush. If the roller becomes clogged with hair/debris, the bearings will sieze, and sometimes even melt the plastic. the roller then has a difficult time turning and will break the bel ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

New main belt alignment for Hoover Windtunnel Mach 6.1. Belt moves 1/4 inch towards of vacuum cleaner and will not stay aligned on the V convex guide pulley

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=853508\015\012Generic problem for all Vacuums\015\012New main belt alignment for\015\012Posted by donle ... Vacuums

Belt will not stay on hoover windtunnel s3765

The Hoover Windtunnel™ Self-Propelled models have two belts, a flat belt and the V-Belt. This V-Belt is the one that drives the Brush Roller. \015\012Aft ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

When I turn on the Hoover U5780-900 it seems the motor just starts to rev up and stays that way until I shut it off. I have replaced all the belts, made sure there were not any blockages, and checked the filters. It still does it. Any other ideas.

... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have an L shaped piece of metal with a hole at one end that fell out of my hoover elite bagged upright vaccuum cleaner. I repaired the belt but don't know where this metal piece goes. I think it has something to do with the wheel assembly which is replaced and it seems to want to stay there. any thoughts

This metal clip was for the wheel assembly, but not always needed. you can diregard the part if your vac is working correctly with the front wheels. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Belt won't stay on - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

A belt will slip off because it is stretched, or the brush bearings are worn, or the motor drive shaft is misaligned. Hoover belts fit snug. After as little as week they begin to stretch. Even though they are not broken, they will spin lo ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover Windtunnel - the belt keeps coming off & it is the correct

One compatible belt that I use and works (at least while its new) is Royal 104425001. Try that. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?

No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums

New belt won't stay on

Take it in for diagnosis - seems to be an offset perpenducular drive axis.. seems to me. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover u6616-900 WindTunnel, belts come off system.

In order to seperate the hood from the agitator housing you will need to remove the screws for the bottom plate (4) remove the plate. next you will see (2) screws. one will be by the belt side the other is on the other side by the sucktion inlet. onc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

My Hoover U6439-900 also losing belts

The belt(s) are probably stretched or worn. This particular model has two belts. You can find them here:http://www.vacbelts.com/hoover-38528034-bel ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belt wont stay on

The belt is bad. Been sitting too long. Replace the belt it will work fine. Explanation why is here:http://www.vacuummed ... Hoover Vacuums

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

... Kenmore Vacuums

Belt will not stay on the Eureke Whirlwind. Changed 4 times and still will not stay on. And yes, it is the proper belt.

... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??

This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.

... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo

The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0483 seconds