Having problems with your Hoover S3765-040 WindTunnel Bagless Canister Vacuum ?

The electric motor in the Power Nozzle does not work when the turned on.


Answers :

There could be several issues with this. First determine if the problem is in the nozzle, hose or wand. This can be done by turning the unit on and wiggling the connections. One known issue with canisters is the cord that sticks out the back of the power nozzle goes bad, due to movement and normal use. There are also 2 electronic control boards inside the canister that give some problems. If you are unsure about looking at it, take it to a qualified repair shop.
Repair Help & Product Troubleshooting for Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The electric motor in the Power Nozzle does not work when the turned on.


There could be several issues with this. First determine if the problem is in the nozzle, hose or wand. This can be done by turning the unit on and wiggling the connections. One known issue with canisters is the cord that sticks out the back of the p ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

The power nozzle works but only on tile. the brush does not turn. the belt is intact. could the motor that turns the belt be broke? is this something i can replace myself or is it better to bring it to be serviced


Depends on you if you feel you could possibly repair it by replacing the electrical motor or you may just have a wire thats nolonger getting continity. enevitably it's your decision if you can repair it you will come off cheaper :) ... Electrolux Guardian Bagged Canister Vacuum

Same problems - power nozzle motor does not work after cleaning the brush and pressing the reset button. Also the handle button which turns on the nozzle does not light up (my wife thought it lit up before).


Hello,\015\012\015\012This is a pretty common problem on the Guardian, and it's usually caused by 1 of two things. Both are pretty simple fixes. The first thing you should try is simply eliminating the wand assemblies from the vacuum c ... Electrolux Guardian Bagged Canister Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Power nozzle motor will not turn on


Try hitting the reset button,It is a small button on the top of the brush and make sure the switch is turned on on the handle. ... Electrolux Epic 6500 Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

I was vacuuming with the regular nozzle and all was well. Then I changed to the powered nozzle and the 2nd power level wouldn't work and then when I detached the powered nozzle I was unable to turn it ....there was no suction. The lights are on for low and high level but not middle level power.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?


That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

Power nozzle for rainbow vaccum is getting power but the motor does not work nozzle model r-2800c


Hi there it's SmartAlec from NelsonVacuums.com.au here. It will either be the fuse or the motor itself. If you disconnect the wires from the fuse and join them together and ... Vacuums

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.


... Vacuums

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like


I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.


... Vacuums

Kenmore vaccuum upright moded#721.33289030 vaccuum worked just fine turned it off for a minute turned it back on the light comes on but theres no power from the motor Please Help thanks Valerie


... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Rainbow E Series Power Nozzle I'm not sure which part of it is not working?


<p>The power nozzle brush roll bearings could be locking up from hair and debris wrapped around them. If that is the case, then the brush roll will be hard to turn and will cause the belt to heat up and give a burning smell. If you need to spea ... Rainbow E series Canister Wet/Dry Vacuum

I own a Hoover Steam Vac Plus w/ Rotating Brushes (model#F5871-900), when I turn on the power I hear a medium-loud hum coming from the motor area and nothing works. What could be the issue?


The motor sounds locked up. Water gets in there and rusts the pieces together. The motor could be replaced, but probably not repaired. ... Vacuums

Rainbow Vacuum, about 5 yrs old (bought new, no issues prior) - my 6yr old tipped it on it's side while water was in basin. Now when I turn the power on, it makes a very loud sound in the motor and you can feel the vibration on the floor. The suction still works and basin still catches dirt - the noise is just so loud and I'm not sure if I should continue use or how to fix -?


Although a wet/dry vacuum, it cannot tolerate water in the motor. Water will cause the motor to short out, which will cause the motor to act/sound like yours does now, if it continues working at all.\015\012To prevent additional problems, the ... Rainbow E series Canister Wet/Dry Vacuum

The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.


It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.


Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

After changing bag, vacuum motor does not work. Yes, it is closed. Yes, the correct bag was used. Yes, the power head bristles will turn, but there is no suction. This is a 3 month old vac. What to do?


If your carpet is quite new then sounds like its choked .Clear out all hoses check for blockages.. ... Electrolux EL6988A Bagged Canister Vacuum

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0998 seconds