Having problems with your Hoover self propelled wind tunnel ?
Roller brush wont turn even after replacing both belts seams like a lot of slack hoover self propelled wind tunnel
Seams like a lot of slack
Repair Help & Product Troubleshooting for Hoover self propelled wind tunnel
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum
Hoover Wind tunnel self propel not propelling - how do I know if it is the belt or the idler arm?
... Hoover U6485-900 Windtunnel Bagged Upright
Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle
Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums
HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED
Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum
I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?
There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.
No don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Self Propelled Wind Tunnel Turbo Powered 7600 The thin belt too loose
If this is a "V" belt, make sure the small roller that tightens the belt is ok and not jammed up. It may have to be replaced. Also if the flat belt is stretched at all, it won't work either. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How do you change the belt on a hoover wind tunnel vacumn/ not self propelled?
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Wind Tunnel Upright Self-Propelled
Thanks to reddevil6. Sure enough it was the belt. What I did was take off the belt and flipped it over, worked like a charm. Since it was stretched on one side the other side was still ok. Still need a new, but s aved me a trip to the store! ... Vacuums
Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?
This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Self Propel doesn't work on Hoover Wind Tunnel
Your self propel wire could be broken. Lean the vacuum back like you were using it. If you stand in front of the vacuum look down and to your left. When you move the selp propel button you should see a wire move. If not then it's broken. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Hoover self-propelled wind tunnel doesn't self propel going backwards.
Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums
My self-propelled Hoover wind tunnel vac. cleaner is hard to push
... Hoover Vacuums
Repplacing power cord on Hoover Wind tunnel (not self propelled)
I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Repplacing power cord on Hoover Wind tunnel (not self propelled)
HiThis is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.
Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums
Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac
On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover wind tunnel u5755-900. smoke, smell. self-propel
Can you verify the model number? However, based on your posted description, it sounds like the flat belt is either broken or fell off. to access the belts turn it over and remove the bottom plate (4 screws). the Flat belt will connect to the motor sh ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Hoover wind tunnel won't self propel
There are really two reasons why the self-propelled wouldn't work. It could either be the belts on the vacuum cleaner are stretched or broken. The belts on this model control both the self-propelled transmission, as well as the brush roller. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Brush not working on self-propelled wind tunnel U6471-900.I have replaced belt but can't get off top cover.
I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums
Hoover Self Propelled wind tunnel vacuum U6433-900
I need to replace the actuator pivot arm on my Hoover Wind Tunnel to fix the self propel feature. I can see where it needs to go but I can not seem to get the cover off the vacuum so I can get to it. How do I do this? ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected].com
If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums