Having problems with your Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum ?

Can't get bottom plate off hoover model

\015 Can't get bottom plate off hoover model u4617-190 upright it takes belt#38528-027 thank you\015

Answers :

Am a bit confused because I can't find the model number you give on the Hoover website, so am not sure exactly which machine we're dealing with. However, the procedure for removing the bottom plate is common to most self-propelled upright wind-tunnel models, and it's simply a matter of laying the machine flat, turning it over and removing the four recessed screws that hold it in place. It can then just be lifted off.\015\012If this doesn't work for you, perhaps you could confirm the model number and I'll try again. It will also help if you say what country you're in.\015\012Good luck!
Repair Help & Product Troubleshooting for Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Can't get bottom plate off hoover model

Am a bit confused because I can't find the model number you give on the Hoover website, so am not sure exactly which machine we're dealing with. However, the procedure for removing the bottom plate is common to most self-propelled upright wind-tunnel ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no

... Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Cant get the bottom plate back onto my dyson upright DCO7i

You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

Trying to get bottom plate off Electrolux upright

Step 1: UNPLUG YOUR ELECTROLUX VACUUM CLEANER.\015\012This is definately a belt change that can get expensive if you break\015\012something. I do not like the idea of a regular person changing this\015\012belt. I've seen people crack th ... Electrolux Cascade 140 Bagged Upright Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.

... Hoover Vacuums

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.

Model no. req ... Hoover Vacuums


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!

Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.

Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J

There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

I have a handheld steam cleaner model mc1220 and i cant get the lid open .what can i do to get it to open.thank you.

... McCulloch MC1275 Steam Vacuum

I have a portable shark steam cleaner model sc505 and my safety cap will not come loose i cant refill my machine until i get it off can you give me some advice on how to do so yhank you

... Vacuums

I need a hose for a Kenmore vacuum. The serial number I found is D80501276 and model numder is 116. Another number on the bottom is 2841080. Where can I get these? Claire Salter

Go to the Sears appliance center. They should have parts for vacuums at least up to 10 years old.Sometimes vacuum cleaner repair shops have hoses that are used that may work. Check in your community. ... Vacuums

Bissel shampooer I have a bissell shampooer powersteamer power brush model 1694-W. I cant get it to dispense water onto the carpet anymore. I think it's because I let my 3 year old ride on it while I was shampooing. I assume I have depressed some special little part that is now broken or mashed or something. Stupid I know....

Yes there is a belt on the side that will need to be changed ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.

... Eureka Sanitaire S661 Bagged Upright Vacuum

I cant get the water to spray out the bottom - Vacuums

Alot of time if the unit is not properly cleaned out after the last use it get a small clogg in the line If you have or no someone who does have an air compressor. Just open the unit up find the nerest opening to the sprayer assy. with just a little ... Vacuums


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

Replacing belt on kenmore quick clean 30012 & cant get plate off

... Kenmore Quick Clean 30012 Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello, My mom has given me her Bissell carpet cleaner. (It is NOT a vacuum.) She has lost the manual!!!! Could you get me one? It is a Bissell Power Steamer Pro, Model 1697 Also at the bottom of the cleaner it says "Dirtlifter Power Brush".

Here is a link to the manual at Bissel's site:http://www.bissell.com/images/UserGuides/1697_908.pdf ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0607 seconds