Having problems with your Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum ?

Is there any way to patch a small hole in the lower hose of my hoover windtunnel bagless? I think my rabbit nibbled on one of the ridges.


Answers :

Usually any kind of strong adhesive tape will do like electrical tape or carpet tape. A small piece should do it fine but if you can try and put a piece inside the tube so that the hole is sticky on the outside of the hose. Then put another piece over the hole on the outside to seal it. Its a tricky operation but if you are patient easy enough to do but needs very close attention. Also make sure that the tape is sealed across a flat part of the hose, not across metal ridges as when the hose is stretched the ridge part that usually has a metal coil inside will stretch and is no good for any hose if a hole has been made against the metal part.
Repair Help & Product Troubleshooting for Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is there any way to patch a small hole in the lower hose of my hoover windtunnel bagless? I think my rabbit nibbled on one of the ridges.


Usually any kind of strong adhesive tape will do like electrical tape or carpet tape. A small piece should do it fine but if you can try and put a piece inside the tube so that the hole is sticky on the outside of the hose. Then put another piece ove ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I think its a hoover any way,i guess at one time some one vacumed up some moisture i can se it on the bottom of motor,on one of thewires theresa thermol senser and i see rust in the plastic,cause it good and thencuts out i think the senser out because of the rust in it???????


If mositure got on it, it could have damaged it and hopefully the motor didn't receive any moisture on the inside of it. ... Vacuums

Hoover windtunnel hose clogged - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have the Hoover Windtunnel Bagless U5753 (purpleish one)


You have a broken belt. This is a very common problem. The belt is designed to break if something becomes caught in the brush roll. This is intended to protect the motor from becoming jammed and burning out. The belt is very easy to replace and your ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Bagless Windtunnel (tank tyle) selfpropeled head throws belt; 2nd one doing exactly as the first vacumm.very hard to put it back on .can't even get one room done


Is this a new belt? If not, get a new one. Check the brush roll, make sure the ends are turning freely, if not, replace it. If you are catching things like a throw rug and towell or some other thing, this will cause the belt to get knocked off of ... Hoover Vacuums

Very little suction on my Hoover Windtunnel Bagless twin chamber vaccum hose while using the tool attachments


... Vacuums

REPLACING SUCTION HOSE - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

No power My Hoover S3765-040 WindTunnel Bagless Canister Vacuum does not seem to receive electricity to power the vacum. One day it worked and the next it did not. Any recommendations for a solution.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

How do I use the extension hose - Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum


Go here for the manual > http://hoover.com/file/493/ ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

How do I install a hoover windtunnel vacuum cleaner belt. The bagless one,.


First, take it outside or to the basement. This can get messy. Turn the vacuum cleaner upside down. Remove four 1-1/2" self-tapping screws that hold the bottom cover in place (where the beater bar is.) Remove this and you will see where the belts go; ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

Hose is clogged - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problemand the hose is clogged...Bissell Bagless Upright Vacuum not work ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel bagless canister fuse - Hoover S3755 WindTunnel Bagless Canister Vacuum


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover Windtunnel Bagless bolt fell off


With this self propell series, the entire bottom needs to come apart to re-install the nut. if it is one month old I would highly recommend taking it in for warranty service. What plastic is melted? ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Loss of suction in my Hoover Windtunnel bagless selfpropelled upright


There's also the possibility that the fan/impeller has stripped loose from the motor shaft and is basically sitting there while the motor turns. Also, you may have broken vanes on the fan/impeller that will drastically reduce the suction. Replacemen ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover windtunnel hose removal - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel model 6626 900 no suction - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0914 seconds