Having problems with your Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum ?

Self-propelled windtunnel bagless

\015 My vacuum is three months old and it is picking up debris but it is not going into the dirt cup it is clogging up in the hole and spitting it back out. the dirt light is not coming on it just stays lit up on the clean light.\015

Answers :

Either the inlet down by the brush roll is clogged, or the hose is clogged. Check that out and if you still have a problem, then take it to a warranty repair shop, you have a 1 year warranty on this. Take your sales slip as proof of purchase.
Repair Help & Product Troubleshooting for Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Windtunnel 721.35820500 not picking up - Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum


I had the same problem - I found the elbow behind the brush was plugged. You have to remove the floor brush, canister, and hose. Look into the pipe from the top, looking toward the floor brush. Most likely, that's where its plugged. Also check th ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Ball bearing fell out of hoover - Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Unit does not self propel - Hoover U6616-900 WindTunnel Bagless Upright Vacuum


You need to replace the belt that propels the vacuum. This is the belt you need:Hoover 38528035 Belt ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

How to replace rocker switch - Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Self-propelled windtunnel bagless


Either the inlet down by the brush roll is clogged, or the hose is clogged. Check that out and if you still have a problem, then take it to a warranty repair shop, you have a 1 year warranty on this. Take your sales slip as proof of purchase. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My self-propelled windtunnel bagless hoover does not pick up.


Remove the dirt cup.\015\012Remove the filter screwed in at the top of the dirt cup opening.\015\012Remove the hepa filters on the side of the machine.\015\012Clean all filters and re-install them. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover turbo power 8000 manual - Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Just put handle on windtunnel u6401-9rm and the self propelled switch will not flip into self propel mode. is there an adjustment on the self propel part?


When installing the handle on this machine, you must be sure the on/off switch and the self propel button are both in the OFF position. The actual switch inside must also be OFF, and the metal fitting on the end of the power drive cable should be bet ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Self-Propelled WindTunnel U6436-900 cable problem


The flat belt should be changed if it has been longer than 9-12 months. Next I would remove the upper handle to inspect the top section of the control cable, sometimes it fray's and has a sponge feel (no positive control) to self propel. To set this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have hoover WindTunnel Self Propelled Vacuum


Greetings from GoVacuum,Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacing Main Body on Hoover Windtunnel Self Propelled


... Hoover Vacuums

Hoover windtunnel self-propelled - will not turn on


You probably need the switch replaced. It's fairly simple to do youself, and it is a known problem with these vacuums.\015\012You can order the switch from hoover for about $10 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt


I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self Propelled Handle Release Lever broken


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Self-propel not working on my Hoover Windtunnel


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover Self-Propelled WindTunnel, U6434-900 on/off switch doesn't


... Vacuums

Hoover windtunnel self propell switch jammed up and wont turn


Here is manual > http://hoover.com/file/552/check out the link below ... Hoover UH5000 TurboPower WindTunnel Anniversary Upright Vacuum with Pet-Hair Tool, Self-Propelled, Bagged

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?


Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together. ... Hoover Vacuums

Hoover Windtunnel bagged self propelled drive not working


Click the link below and watch video how to fixhttp://www.youtube.com/watch?v=K722IsUxjYM ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0261 seconds