Having problems with your Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum ?

A piece fell out when I was emptying the bin and I can't figure out where it goes. Gray, about 4 inches long, strait with small pegs down one side.

Answers :

It sounds as if this is the piece desinged to scrape lint from the screen on the filter cartridge holder. There should be two slots near the top of the dirt cup, about in the middle, that this piece snaps into, with the pegs facing the filter.
Repair Help & Product Troubleshooting for Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

A piece fell out when I was emptying the bin and I can't figure out where it goes. Gray, about 4 inches long, strait with small pegs down one side.

It sounds as if this is the piece desinged to scrape lint from the screen on the filter cartridge holder. There should be two slots near the top of the dirt cup, about in the middle, that this piece snaps into, with the pegs facing the filter. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher

If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

I have a Tomy Up Down Change Around Roller Coaster that does not power up. I disassembled it and it has a small unmarked rechargeable battery. The coaster car is supposed to hook into a unit that holds one "D" size battery and has two metal prongs that press into the side of the car. Any advice on what the battery type might be or how to find out?

... Vacuums

During re-assembly of my conair (model HC91RS) i noticed that my two blades do not line back up. The big blade sits evenly in it's space but the small blade is tilted slightly to one side. Is there any other means of aligning these two blades?

... Vacuums

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th

Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?

Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

2002 esb avalon tanning bed 220volts. 2 lights out on top side by side and two on bottom side by side and one by itself checked all fuses on top and bottom one was blown changed it to new fuse and it blew right away what could be the problem

... Vacuums

One of my Levolor double-honeycomb blinds is no longer level (one side goes up faster than the other). Another of my blinds (same brand, model) seems to have broken, with one side no longer rising. Both blinds are about 9 years old. Is there any way to fix them? Or, does it make more economic sense to replace them? Thank you!

Hello,\015\012\015\012This problem is a common problem on this device, there are many people\015\012who are searching for the answer on what to do and what are the causes\015\012of this problem. The answer to this is still not clear. ... Vacuums

I have a hoover light & soft upright sweeper. In replacing the belt a "v"metal clip popped out. It is metal in a shape a "v" with one hole on one side and jagged edges on the other side. Where does it go and how to re-install it????

Its actually for your height adjustment, take off head again and you will see in middle there is alittle grove that fits that piece precisely..let us know ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

My Roomba 570 will not go forward. the only thing that it will do is rock side to side or turn to one side then to the other side. The it turns it self off and gives me display signal of "!". I have replaced both wheels.

... iRobot Roomba 570 Robotic Vacuum

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks

Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

Hi, we have a Sunbeam electric blanket model no. BLO750 and type 696. It's a double blanket with dual control that can be used for different settings on either side. Both sides have been working ok but last night one side wouldn't heat and the green light kept flashing and now, whatever we do the green light keeps flashing except, when we set the control to "off". We can't find our Owners Manual to see what we are doing wrong, can you help please...or can you advise us where we may be ab

... Sunbeam Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C

... Filter Queen Majestic Canister Vacuum

I bought a fantom vacuum on HSN about 9 years ago.Whan it was delivered the first one was broken so they sent a second one.tThat one also was cracked on covering for brush. I called and they told me they were no longer available,so I kept that one,since it would cost me shipping to return.The back right side wheel evenually cracked and fell off.I was able to put it back on and it would stay for a few weeks or so.It now has a large piece of plastic that has broken off the wheel where the bolt fit

... Vacuums

Replacing the old chamber filter (cloth on both sides)with filter that has cloth on one side black foam on the other. Which side faces the bag?

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet

Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Sleeptight Imetec Electric Blanket with timer and Dual Controls one for each side of the bed recently the timer was set for 45 minutes and when 45 mins elasped it went off and the control light began to flash which is normal however it is since stuck in this mode light flashing will not heat just keeps flashing is there any way of sorting this the other side of the blanket for the other side of the bed seems to be ok although it did the same thing but reset itself any ideas Regards

... Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?

I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0509 seconds