Having problems with your Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum ?

Have an older Dirt Finder U6331. the self propel cable does not seem to engage when working the top handle. Is their an adjustment or repair I can do?


Answers :

You will have to replace the handle or the cable both of them wear out with time and use
Repair Help & Product Troubleshooting for Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have an older Dirt Finder U6331. the self propel cable does not seem to engage when working the top handle. Is their an adjustment or repair I can do?


You will have to replace the handle or the cable both of them wear out with time and use ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.


Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

The self propelled feature does not work. Belts are OK but the drive wheels do not seem to be engaging. Is there a cable or something from the lever on the handle that needs to be replaced?


My vacuum cleaner does not turn on \015\012could it be the motor out \015\012i check the switch it ok not getting any power to the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a futura II 920 machine and the bottom/bobbin tension is not working. no stitches are being made. i rethreaded the machine many times and adjusted top tension, still will not pick up bottom thread. we have no singer repair in our area can you help


I don't know whether I shall provide you this solution or not but the repair manual for your machine is not available. It's available for a purchase specially for fixing bobbin tension.\015\012\015\012In case you don't wish to buy it kindly ig ... Singer Vacuums

I have a durabrand food steamer model number FS1146R (ASDA spec code: 195/121). it is white a the bottom with a timer and has two clear plastic steamer compartments. The problem I have is that the handle on top of the lid has broken off. My husband has repair it a couple of times but can't do it anymore. Is there any chance I can purcase a lid as the rest of the steamer is still in good working order. How much would the lid cost? Many thanks Barbara Waller


... Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Assembly I am trying to assemble the eureka smart boss. The problem that I am having is that the handle is not completely fitting into the cleaner body. I can slide the handle into the handle supports but it doesn't seem to click together. There is a space at the top; it doesn't seem to be able to fit as closely as the bottom. Thanks, Lisa


It may not just slide into place, you may have to knocj it into place, then put the screws in to secure it. ... Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?


... Hoover U5468-900 WindTunnel Bagged Upright Vacuum

We have the 3910T model. I am trying to get the height adjustment to work. I had taken apart the portion to change the belt and for some reason the height adjustment is not working. Is there a diagram on how to have the knob engage the other part?


... Bissell 3910 Bagless Upright Cyclonic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

For some reason the adjustment thats in the front for lowering and highering doesn't seem to be working is there a manual that I could see in adobe that would show me how this is supposed to be I think I have it on right but when I look at the bottom to adjust it doesn't seem to do nothing [email protected]


My printer will not fax it says modem no exheistence?\015\012what does that mean and how can i get into fax settings ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I bought an old Juki Baby Lock 418 at a garage sale. It will sew for 3 or 4 inches and then seems to be off timing and locks up. I have no instruction manual. Is there a manual available for this old machine? I would prefer a downloadable manual because I already have money invested in the machine which doesn't seem to work. It was suppose to have been gone over at a repair shop before I purchased it and was told that it worked. .


... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I have a tear in the top of my hose. Right by the handle is there a way to shorten the hose a few inches at the top to repair the hole?


You'd be better off using duct tape on it. Ensure the wiring is intact first, then wrap a couple wraps of electrical tape around the hose, then 2-3 of duct tape. May not be pretty, but safer than cutting the hose and wiring just right to get everyt ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Kirby G5 vacuum that when light pressure is put on the handle it moves forward but in a jerky movement. Like the drive is engaging and disengaging. If you keep forward pressure on the handle the jerkiness does not happen. Is there an adjustment to correct this.


I hope adjusting position of the position of the "pivot spring assembly" will help. but you may have to disassemble entire slide assembly to clean it up if it still does not work smoothly. See instructions ... Kirby G5 Bagged Upright Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

When I engage the beater roller it will work for a short time (15-20 seconds) and then squeel loudly as if something is not engaging properly. I checked the roller ends and cleaned them but it seems to roll freely by hand while connected to the belt and then at a time it becomes very hard to turn by hand.


Sounds to me that the motor is shot. There is a main bearing the belt shaft connects to and it sounds like the bearing is seazing and gets worse when it nheats up. Soon it wont turn anymore at all ,once it siezes completely. These are rarely worth f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.


... Euro-Pro Vacuums

Hoover Windtunnel On/Off switch will not turn Off...Switch seems to work O.K. when pressed directly but not with handle switch...It will turn on but not off..Cam seems to be intact on switch actuator..How does switch come out? Thanx


Take the handle off, then remove the tool holder, then you can get to the switch. Just has tabs on each side of switch, depress them and push it out. These switches will do this after awhile, replacing them is usually the way to correct the problem ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

With my K6 Industrial Singer sewing machine the top thread seems to be too tight. The bottom thread is looping too much on the top of the fabric. The timming is ok. I have checked and rechecked that I have threaded it correctly. It was working great the other day. Please help as we are live out on a property and too far out to get someone out to look at it. Thanks Tania Sorry no category for sewing machines on your list


Hello there, loosen your top thread tension,if it looping on top of the material the tension is way too tight, you will also find changing the thread size to smaller thread, the top tension will also reduce,depending on application a good size thread ... Singer Vacuums

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,


You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

No Suction I have the Eureka Upright Vacuum. I have no suction when doing regular vacuuming but it seems to have function with just the hose. Also, the height adjustment doesn't seem to work at all. The vacuum has only be usede 3 times. Thanks


Is your brush roller turning? unplug the vacuum and see if you can turn the brushroller by hand.if it turns real freely the the belt is broke ,if its real hard to turn then something is caught up around the bearings on the ends of the roller.my sugge ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1070 seconds