Having problems with your Hoover Steam Vac Dual V w/ SpinScrub Vacuum ?

Help for free???? my spin brushes won't spin

\015 My brushes won't spin\015

Answers :

I have the 7443-940, and on this one, the brushes are powered by the water coming from the water pump. If there is no water in the unit, they will not spin. I do NOT know if yours is the same way, but it's worth trying it out.
Most probably cause is the belt is broken, replace it.
Repair Help & Product Troubleshooting for Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Help for free???? my spin brushes won't spin


I have the 7443-940, and on this one, the brushes are powered by the water coming from the water pump. If there is no water in the unit, they will not spin. I do NOT know if yours is the same way, but it's worth trying it out. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Dirt Devil Model 088520 has a brush assembly that wont spin. How can I either change the bearing or free it up somehow? I have been searching for a new brush assembly part number 2860145000 but it


Try this link > http://dirtdevil.com/parts/category/brushrolls-uprights/ ... Dirt Devil Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times


Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover Vacuums

The brushes at the bottom wont spin round or pick anything up?? help


The belt needs to be changed. to replace the belt remove the screws on the bottom of the brush housing and you will see hte belt, make sure the spindles that the belt goes on are clean. ... Vacuums

The suction on my oreck is good and my belts are fine, brush is spinning, but wont pick up anything when I vacuum. Help?


Sounds like a full bag or an obstructed passage ... Oreck XL Ultra Bagged Upright Vacuum

Brush wont spin


Was the belt worn or broken? It probably needs to be replaced. Here is the belt you need:Dyson DC07 Belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand


In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Dyson DC 28 brush bar wont spin


... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

No suction power ,brush wont spin on carpet power nozzle. When it


You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Agitator brush wont spin once vacuum is placed on floor


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618889&thid=573865\015\012Agitator brush wont spin once vacuum is placed on...\015\012Posted by coral7980 on May 05, 2008\015\01 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Bissell powersteamer clearview model 8806-roller brush wont spin


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.


I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

My hoover spin brush steam vac brushes wont spin


Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?


As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?


... iRobot Roomba 530 Robotic Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

DC07 brush wont spin on bottom, took all apart and wont work


Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

THE BRUSH WONT SPIN AND THE SOLUTION WONT COME OUT


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin


The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.


You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Help. The brushes on my Steam Vac Spin Scrub


If you don't have the user's manual for the machine, here it is:www.thinkvacuums.com/pdf/uprights/Hoover_F5914900.pdfCheck your system for any obstructions that could possibly causing the problem. Also, remove the brushes and see if ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0772 seconds