Having problems with your Hoover Steam Vac Dual V w/ SpinScrub Vacuum ?

How to take apart hoover steamvac all terrain

\015 Take apart\015

Answers :

Repair Help & Product Troubleshooting for Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to take apart hoover steamvac all terrain


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman


\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

Is it possible to take the Hoover Brush Block Assembly F7220-900 #48437029 apart so that I can thoroughly clean inside the block? It looks like it could, but I don't want to break it by trying.


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Found old Hoover "Concept One" and need to take it apart


... Hoover Vacuums

Vacuum, Hoover Elite 350. Rag sucked up how to take apart


... Vacuums

I have a Hoover F5411 steamvac Jr spot cleaner and it won't spray and one of the answers was to turn it over and try to turn the impiller to see if it turns. Where is the impille? Is it on the bottom of the top of the steamvac or on the bottom of the part that takes in the recover water?


... Vacuums

I need to take apart a vax cylinder hoover to service it


... VAX Appliances 2000 Canister Vacuum

How do I take my SteamVac F5914-900 apart again? You helped once before


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac F7226900. Bottom of clean fill tank cracked, how do I take off the black plastic piece around the bottom of the tank without breaking it? Thanks!


Try this link belowhttp://www.ereplacementparts.com/hoover-f7226900-steamvac-parts-c-37315_37419_202371.html ... Vacuums

I want to take apart a hoover core vac


... Hoover Vacuums

I HAVE A HOOVER VACCUM CLEANER MODEL U8172-900. i HAVE TAKEN IT APART AND CANNOT TAKE THE TOP COVER OFF TO CHANGE THE BELT. CAN YOU HELP ME?


This must be a Savvy, Take off the plate covering the brush roll, then take out 2 screws from the bottom, turn it over, remove the Hoover emblem, there is another ***** there. Then the top cover will come off. ... Vacuums

My hoover windtunnel u6323-930 has dust leaking into air when unit is on. i think it is in the housing I cannot see and I need ti know how to take apart to determine which part i need to order thanks David Macali


You will just have to start taking the base aprt until you can get the motor, Just remember how it was so you can put it back together correctly again. When you have the motor off, look at the fan chamber, you probably have a crack or hole in it. ... Hoover Vacuums

Hoover Steamvac hose won't spray water


SOLUTION#1 If the attachment wont spray water, the white plastic nozzle tip may be clogged. Take the brush attachment off, remove the two screws from the gray retaining cover (BE CAREFUL THE WHITE TIP UNDER THE BLACK PLASTIC TRIGGER MECHANISM IS SPRI ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?


Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

My brushes on my hoover steamvac all terrain carpet and hard floor cleaner will not spin what do i do


I am not sure if you have the F7222 or F7452 all terran. There is a plastic piece on the back of the block brush (spin scrubbers) these wear out or break. You may need to replace the block brush. You can find the parts below follow the link. P ... Hoover STEAMVAC VACUUM Vacuum

I need to know how to put together a Hoover Slider vaccum. I had to take it apart and now i need to put it back together.


... Hoover S2105 Slider Bagless Stick Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

Hoover all terrain steamVac brushes wont move. Does this model have a belt and where


The brushes are driven by air flow (suction). the most likely problem is with the turbine. This part can be replaced or repaired. If under warranty, take it tin for service, otherwise you will void any warranty. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Hoover SteamVac Deluxe and it will not spray the detergent. I have taken it apart and still can't solve the problem. Any help or suggestions?


If yours has separate tanks for the solution and water, it is a pressure regulator switch. It happened on my mine and I replaced it. 3 hoses attach to it and it was located in the handle area on mine. If you mix your own solution in one tank, look ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

The on off switch is stuck in the on position. I can'tfigure how to take the handle apart. Where can I find an on-line manual? Hoover wind tunnel up-right.


On the windtunnel the switch is not in the handle. It is located in the top of the body housing underneath where the handle meets the body. The slide lever you are pushing on to make the machine run is just a push rod. ... Vacuums

Hoover steamvac brushes don't spin. everything else works great. Took it apart and no visible problems


My husband took it apart today and the impellers were gunked up with black stuff. \015\012\015\012he used these pictures that someone else generously posted. ours was slightly different in internal design, but they are helpful regardless ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0676 seconds