Having problems with your Hoover Steam Vac Dual V w/ SpinScrub Vacuum ?

On my Hoover SteamVac SpinScrub,Model F5915905 the middle brush fell out of socket. Keeps falling out. How can I fix this problem?


Answers :

Repair Help & Product Troubleshooting for Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On my Hoover SteamVac SpinScrub,Model F5915905 the middle brush fell out of socket. Keeps falling out. How can I fix this problem?


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.


This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor


... Eureka 3041BZ Upright Vacuum

I have a Hoover SteamVac F5914-900 that I purchased approx 6 mos ago. It just started having the following problem. When I turn the cleaner on there is a sudden burst of solution/foam that emits out to both sides from behind the brushes. How can I fix this??


Mine has been doing that occasionally, and I have ordered the pump assembly, #H43582003 which several have suggested is where the problem is. This leak, along with loss of solution going to the hand tool, seems to indicate that the pump is not workin ... Hoover V1 SteamVac SpinScrub Vacuum

Middle brush fell out of Hoover steamvac F5914900


... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a Shop Vac (Wet/Dry) Model 5275 (120V 60Hz 6.4A), Peak HP of 2.75 While vacuuming the Shop Vac fell over, stopped working, and would not come back on again. Tried plugging into another outlet, etc., but nothing works. Is there some internal problem that I can fix myself?


... Shop Vac Vacuums

Hi. I purchased a Simplicity Freedom about 2 years ago. I have had it in for various repairs several times. One persistant problem that the repairman cannot seem to fix is the dirt does not fall down into the bag - it just stays up around the suction hole. I only use simplicity bags. Any suggestions would be most appreciated. thank you


You can let the vacuum run alittle longer so the bag fills up with air, also make sure that the bag in on correctly and you have the right bag for the unit. Let me know if this helps. ... Simplicity Vacuums

The tiny hose for the steam has fallen off how do I fix this problem


You need to replace go to www.eurovac.com and buy it.God bless you ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.


If it heavy then do some muscle work and body building ... Vacuums

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.


... Vacuums

Hei, I have sewing machine Brother NV500D and got technical problem need to be service/repair. I'm now in Malaysia and don't have techinical/repair service for sewing machine NV500D. This is overseas model. In sewing machine screen display 'F04'. The problem automatic needle not function and part missing. I dont no how to fix this. Can't i got the instruction manual service picture if i can't fix own. please help me. thank you.


... Vacuums

My kenmore progressive vacuum handle release pedal fell off how can i fix this


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Lately we've been having plumbing problems to where our washing machine floods up our bath tub and toilet. And it happens while we have the washing machine on of course. Another problem is that whenever we are taking a shower our tub starts to clog up and water starts pouring out from the bottom of our toilet. We had a plumber come by to root out our pipes just last week and it was fine for about 3 days. And now the problem is back and driving me crazy. WHAT IS WRONG AND HOW CAN I FIX IT??


Possible tree roots best thing is to hire a plumber with a camera snake ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have a singer 328 and the foot pedal has developed a problem the machine is running all on its own can I fix the problem with the foot pedal


... SewShop.com 328 Singer Instruction Manual .pdf format

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.


Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.


I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

How do I fix the overheating problem with my shark upright vacuum the website said someone has fixed it and i was wondering how?


... Euro-Pro UV209 Upright Vacuum

Horrible noise The same problem that has been the other people have experienced, I can make the noise stop if I switch to floors, but it doesn't work well on carpets. Has anyone been able to fix this problem?


It sounds like you have a blockage. Go to this at Dyson to look at your item in more detail. They have good support here for your item. Just copy and paste into your browser.http://www.dyson.com/support/help.asp?product=DC17-ANIMAL&ar ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vacuum cleaner will not shut off when turned on. I have had it serviced twice by Sears, and for the third time I have experienced the same problem. I disassembled the upper have and it appears that the plastic mechanism designed to turn the switch on and off does not always catch the switch. Is there a way to fix this problem.


Put in a new switch, like toggle switch or use one off an old junk vaccum ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Motor smells I have the same problem. Did you get this fixed? Was the problem the motor or the brushes. I don't want to spend $80 for the motor KC92FCJNZ000 is there another way to repair this?


... Kenmore Vacuums

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Renny brush is not moving what do I do? I just had is serviced for $200 and brought it back once already, he is claiming now that it is the circuit board. I do not trust him to fix the problem, can I fix it myself? It also now is not shuting off.


You have two circuit boards in th Renny, one is in the handle of the hose and the other is called a triac located next to the motor in the canister. There is a long and drawn out procedure in trouble shooting the problems with the Renny and if you do ... Electrolux Vacuums

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0422 seconds