Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB


Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell spot lifter: there is no spray coming from the nozzle when I pull the trigger. It turns on and the brushes spin, but there is no way to activate the solution.


Took it back to the store...customer service found a clog...gave me new one that works ... Bissell Vacuums

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My steam cleaner doesn't spray the cleaning solution, instead when you pull the handle to spray it sends the solution to sides and it comes out like a small faucet


... Hoover F5835900 Upright Steam Vacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

I have a Bissell PowerSteamer 1697-1 series. It stopped spraying with the main part and now the hand tool also won't spray any solution--everything seems to be working and it appears to try but it won't spray


... Vacuums

Replaced the pump for a 9300 M Bissell Proheat 2x as the water solution was not releasing to the carpet. Once rehooked the lines the solution appears to be coming from the water tank and returning to the used tank and bypassing spraying on the carpet. How can I be sure the hoses are hooked up correctly?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My Bissel ProHeat carpet shampooer is not spraying to the floor. I have checked the hoses best I can and they appear to be clear, no clogs. The nozzles don't looked clogged either. The above floor hose does spray water. I definitely have not gotten my money's worth from this machine. Any solutions?


... Bissell 9200 Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My irobot scooba does not spray cleaning solution out after about the first 30 seconds it is running. I have tried all the suggestions in this post with the suction bulb to charge with air, and then with water to clean it out. water does come out of both valves when forced with the bulb or immediately after using the bulb to charge it. then after it runs for about 30 seconds the floor is dry.


... iRobot 5800 Scooba Vacuum

The heated solutions only sprays out to the floor in a 3 inch area. It takes a long time to clean the floor with only 3 inches available. Are there some nozzles somewhere on the machine that I need to clear out? If so, how do I access the nozzles?


There are two nozzles (either red or white) on the unit located behind brush. Use an old toothbrush to clean them off and that should resolve the spray issue. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

Same problems - power nozzle motor does not work after cleaning the brush and pressing the reset button. Also the handle button which turns on the nozzle does not light up (my wife thought it lit up before).


Hello,\015\012\015\012This is a pretty common problem on the Guardian, and it's usually caused by 1 of two things. Both are pretty simple fixes. The first thing you should try is simply eliminating the wand assemblies from the vacuum c ... Electrolux Guardian Bagged Canister Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Asking again. Better wording? My lightweight Bissell carpet shampooer is continually spraying cleaning solution. The sucking action works well but can't keep up. This unit does NOT HAVE A HEATER. This is a simple unit. Is there a cable going down the handle from the trigger? ( it feels like that's the way it works. Could the drain be plugged. Also it will only use 1/2 a tank of solution at a time. Then must be filled again


Hi Sue. I understand how frustrating this must be. I'd like to help you with troubleshooting steps, but need more information.\015\012Here's a quick link to contact us: ... Vacuums

I have a Nutone CV-450. When the unit is turned on the motor makes a high pitched whining sound. The suction seems like it is reduced and there is a burning rubber smell coming from the unit. Suction at the unit itself is also reduced. Any ideas about the cause of the problem and the solution?


... Broan-NuTone CV450 Central Bagged Central System Vacuum

Hi my vacuum (Russell Hobss 2200 bagless HEPA) seems to have just enough ( not loads) of suction til it reaches the cleaning head. the head does not appear to be blocked - but there is then almost no suction at all. It also makes loads of noise when on- and an even louder noise when turning off. is it fixable or is it dead? Thanks


Generic problem for all Vacuums\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA)\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA) seems to have just enough (not loads) of suction til ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1297 seconds