Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

My brush keeps falling off the bottom of my steam cleaner


Answers :

The snap in clips have been broken off the brush housing. You will need to replace the brush assembly.
Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brush keeps falling off the bottom of my steam cleaner


The snap in clips have been broken off the brush housing. You will need to replace the brush assembly. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

I have a steam cleaner and i can not get the black arm brush to keep one side up and when you trun on the steam cleaner the brush dose not spin when you start to clean the floor but it will spin when you have it siting up right


Sounds like you could have an elevator broken (part #2000010). You will have to take the top off to replace them or to check to see if one of them is broke. There is one on each side so when the handle is in the upright, they push againsy the brush ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes


(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Need to remove bottom brushes of Hoover Steam cleaner F7452900 to clean


Here is the manual that came with the vacuum if you didn't have it already, in it on page 13 of the pdf shows you how to remove the bottom brushes.www.thinkvacuums.com/pdf/uprights/Hoover_F7452900.pdf ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Dyson curved piece at bottom keeps falling off how to reinstall?


Call me, doug in Riverside cali, pretty handy just rebuilt my stage 3 on my animal. I am incredibly gifted. 951-316-7071 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush will not spin on the steam cleaner - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm


I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

BRUSHES WONT TURN ON HOOVER STEAM CLEANER - Hoover F5891-900 Steam Cleaner


Belt probably broken. unplug from power and remove the plate from the bottom of cleaner.belt should be visible on one side or other. ... Hoover F5891-900 Steam Cleaner

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate


If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

My Delonghi DSS50 steam floor cleaner water reservoir has a broken valve on the bottom where it fits into the steam unit. It leaks water rather than producing steam. I would like to find the valve and replace it or buy a new water reservoir with the valve in it. I cannot find the part I need. Can you help me?


... DeLonghi DSS50 Scopa Upright Steam Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions


Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Solution for "hoover steam cleaner keeps


Hoover Carpet Shampooer\015\012\015\012You might just need a new gasket. THey are inexpensive and fairly straight forward to replace with the ... Hoover F7431-900 SteamVac Vacuum

Replacement brushes for a Vaporetto Sprint 1200 Polti Steam Cleaner


... Polti VT1300 Vacuum

My bissell steam cleaner clear views keeps


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brushes on bottom of Steam Vac


... Hoover Steamvac F5864-900 Vacuum

Polti Vaporetto I have a problem with my steam cleaner. Cannot get steam to come out, and the big valve at the top just keeps turning in both directions. So can't empty it. I have'nt got an instruction manual either as it was given to me. Any suggestions!!! Terena


Dear Terena \015\012\015\012Had the same problem with a polti vaporetto 1500 ( vtt 1500 ) after butchering the big valve on the top I realised that the problem was that there was a blockage in the black pipe that comes from the machine to ... Polti Vaporetto 2400 Canister Steam Vacuum

I need the thermistor (the temperature sensor) that is located on and in the bottom of the steam tank for a euro pro steam cleaner model S3325 with a date code of 1508


You could call euro-pro 1-800-361-4639 or 1-514-842-8691\015\012also if it is the silver bullet micro fuse you are looking for you try google goodmens on the internet ... Vacuums

I can't get the floor brush to stay on - Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum


Sometimes the locking latch gets broke off. You may need to replace the swivel elbo. ... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

I was steam cleaning the stair landing and the steam cleaner slipped off the landing a few inches and the brushes haven't worked since


Please remove the brush assembly by pulling down from the bottom of the cleaner. There is a drive pin to the brushes, approximately 1/4 inch square and two inches long that connects the brush to the drive mechanism. You may have broken the pin off, ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0957 seconds