Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

HOOVER STEAM VAC. I CAN ATTACH THE SOFA CLEANER ATTACHMENT AND THE SOAP WILL COME OUT BUT I CANNOT FIGURE WHERE TO ATTACH THE ROUND PART THAT WILL **** THE SOAP BACK UP


Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOOVER STEAM VAC. I CAN ATTACH THE SOFA CLEANER ATTACHMENT AND THE SOAP WILL COME OUT BUT I CANNOT FIGURE WHERE TO ATTACH THE ROUND PART THAT WILL **** THE SOAP BACK UP


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I sucked up a sock into the carpet attachment of my electrolux 3500 series and the carpet attachment cut off. After the sock was easily removed (it was only wrapped around the brush part) I reattached the carpet attachment, turned the vacuum on and flipped the switch to turn the carpet attachment back on, but it won't come back on. How can I fix it?


Did you press the reset button? There will be a reset button either on the back of the unit just below the bulkhead or on the top side of the base.\012\012Locate the reset button and press; this should allow the carpet attachment to resu ... Electrolux Epic 3500 Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Cannot use attachment when spraying it comes out from below


... Hoover F7431-900 SteamVac Vacuum

Cleaning rollers and belt come off on one side, cannot figure out how to put back.


Hello,For wonderful step-by-step instructions on how to replace the rollers and belt, please refer to pages 17-19 of the user manual located here: ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.


May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if


... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off


It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums

I just bought a Tfal Ultimate Autoclean iron FV 9450. I am reading through the manual and trying to figure out all the parts and functions. I cannot figure out how to remove the anti calc valve. I see it is part # 12 on the drawing but that piece on my iron (the bit with the little circles on it where it says, " anti calc plus') seems to be a flat piece of integrated plastic with no give or slide to it. .I cannot see how I'd possibly remove it. What do you do - push up? push down? The i


Anti-calc valve wings (grip) located at #3 of the 1-15 labeled description diagram that is part of the instruction manual. The wings are on either side of the dry/steam control #4. Lift up on the wings (grips) and the dry/steam control will accompan ... Vacuums

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

My steam mop gets hot but steam is not coming out when i pump it. However when I release the bottom attachment steam comes out of bottom of the base (purple part). I took the attachment off to see if it was plugged but dont see anything. Any suggestions?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?


If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Falling apart http://pdf.oreck.co.uk/user/qvc/OK2483%20Power%20Team%20U38052HHPDQ.pdf part 10 coming away from part 12 whilst vacuuming and parts 11 letting out dust, even when attached. Rubber seals in place and tightened as instructions.


... Oreck Vacuums

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....


Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo


Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL


... Bissell 1200A SpotBot Pet Robotic Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne


... Hoover S3614 Vacuum

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f


I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

I lost the detergent container on my Hoover Model F7220-900. Its a small plastic bottle that sits on the back of the clean water tank. I called the help desk and they told me that they no longer make that part so I have to pay $55 to replace the whole tank which will come with a detertent container built in. The whole carpet cleaner was only worth about $225 new. I don't feel I should have to pay $55 for a part I don't need but the machine is worthless without it. Any good ideas to solve th


... Hoover F7220900 SteamVac V2 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0639 seconds