Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

I have a hoover f5861-900 steam vac. the trigger mechanism seem to not work anymore. Water dribbles out without using the trigger. Taking the water tank out I can see the rod very slightly moving on the diaphragm. I removed the top part of the vac to hopefully reset the rod connection. But, didn't make any difference. I appreciate any help you can give me. thanks


Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hoover f5861-900 steam vac. the trigger mechanism seem to not work anymore. Water dribbles out without using the trigger. Taking the water tank out I can see the rod very slightly moving on the diaphragm. I removed the top part of the vac to hopefully reset the rod connection. But, didn't make any difference. I appreciate any help you can give me. thanks


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia


I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

I have 16981 Model. The trigger assenbly has snapped off the retaining pieces inside the handel. Can you buy a new handle with the trigger assenbly? What is price and part number? Also the lever to adjust the up and down movement of entire handle has broken. Can you buy? Is it possible to fix it and price for part?


The best place to obtain a replacement part for your unit is to either try and download an exploded view of the product, found in a service manual (which is often information restricted to the authorised repair agent), to get to the part number. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I badly need a replacement for the small elasticized grey cloth part (filter??) that fits over the plastic form inside of the hand vac of GE Combiination Vac Bagless System---model 106687, type A. Can you just tell me if the name of that part is the filter? I did find one on a website but there's no image available and I don't want to order the wrong thing. Thank you.


... GE Combination 106687 Upright Vacuum

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.


Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

Need reset button. Have part number. Can't find part online


May I direct your attention to one of the advertisers here at Fixya.com or www.repairclinic.com? ... Electrolux Centralux Vacuum

Replacement parts I lost the tip and tools in a move and now can not find anything about the product and where to get replacement parts. Any help locating a parts supplier would be greatly appreciated.


... Saeco Supervapore 2500 Steam Vacuum

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.


... Hoover Vacuums

Trying to find replacement part for a Bissell Power Steamer Deluxe Model 1631-1, Part Grip and Trigger Assembly Part No. 016-4181


Http://www.bettervac.com/bissell-016-4181-handle-assembly-for-big-green-machine.aspHopefully this helps. ... Bissell Vacuums

I need the part that go's on to the steam handle for the other attchments to work. Let's see that's steam handle missing part then Other Attchments this is the only way I can name it, I hope you can understand what part I need. THANK'S


Hi,\015\012\015\012I have a better solution. Here is the parts diagram for the S3325. Please tell me which number relates to the part you need and I will find suppliers for you and the correct price. If your vacuum is not the S3325, pl ... Euro-Pro S3325 Handheld Steam Vacuum

Part replacement we have one of your "Shark steam cleaners", that while moving from one room to another, was dropped. The head separated from the part that holds the water and broke in the process. Can this part be purchased.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Needing part #600-6083 for Bissell 3-way Vac model #3037. Can't find part on any website. Is this part still available?


Hi there it's SmartAlec from NelsonVacuums.com.au here. If you are in Australia i can help you with any parts for Bissell machines. I would really need to get some extra de ... Bissell Vacuums

Where can I find a part for my BV2000 in house vac? It is the smallest unit made by M S & S Systems in Dallas TX. The suction impeller is grinding in it's housing, so I need a motor/suction pump. I have removed this combination from inside the vac assembly


You will have to replace the whole motor as these motors where never made to be serviceable. if you take the motor to a local vacuum shop than can order you a new one. though i would recomend replacing the whole tank unit with a Nutone or Hayden they ... M&S Systems BV-2000 Bagged Canister Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

Have a kenmore canister vacuum cleaner which the power-mate parts don't work. I had loaned the vac out it came back with part of the hose smashed. I don't know if that is the problem.


The hose conducts power to the "power Mate" There are wires running end to end through the hose and handle. If your hose is grey with hard plastic cuffs at both ends, it is repairable, but you will need to locate the Smashed parts. If yo ... Vacuums

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?


There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0479 seconds